TABLE OF CONTENTS SAFETY PRECAUTION ....3 - Precautions In Installing the Product .....3 - Precautions to the AC Adapter and Electrical Power ..................5 - Precautions In Moving the Product ......7 - Precautions In Using the Product ......7 - Mounting on a Wall ............8 LICENSES ........9 ASSEMBLY AND PREPARATION ......
WARNING - This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. SAFETY PRECAUTION Please read these safety precautions carefully before using the product. WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION If you ignore the caution message, you may be slightly injured or the product may be damaged.
Page 4
If you install the product in a place that does not meet the recommended conditions, this may cause serious damage to the product’s picture quality, life cycle, and appearance. Please check with LG or a qualified installer before installing. This caution applies to a place where there is an abundance of fine dust or oil mist, chemical substances are used, the temperature is very high or low, the humidity is very high, or the product is likely to remain turned on for a long period of time (airport and train station), failure to do so will invalidate the warranty.
- If loosely connected, the poor connection may cause a fire or electric shock. • Be sure to use power cords and AC adapters provided or approved by LG Electronics, Inc. - The use of non-approved products may cause a fire or electric shock.
Page 6
• Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off. - You may be electrocuted due to excess moisture. • If you don’t intend to use the product for a long time, unplug the power cable from the product.
Precautions In Moving the Product WARNING • Make sure to turn off the product. - You may be electrocuted or the product can be damaged. • Make sure to remove all cables before moving the product. - You may be electrocuted or the product can be damaged. •...
CAUTION • Do not put or store inflammable substances near the product. - There is a danger of explosion or fire due to careless handling of the inflammable substances. • When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product.
LICENSES Supported licenses may differ by model. For more information of the licenses, visit www.lg.com. The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Vision IQ, Dolby Audio, Dolby Atmos, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
SuperSign Software & Manual - Downloading from the LG Electronics website. - Visit the LG Electronics website (http://partner.lge.com) and download the latest software for your model. • The warranty will not cover any damage caused by using the product in an excessively dusty environment.
Parts The image may be different according to the model. 75XF3ES Illuminance sensor / IR Receiver Power Indicator NOTE You can set the status of the power indicator in Installation → Signage Setup. • • You can adjust the volume by using the remote control. Portrait Layout When installing in a portrait layout, rotate the monitor clockwise 90 degrees (when facing the screen).
• Observe the following to ensure that the panel surface temperature does not exceed 75 degrees. Enclosure Protective Glass Air Gap LG Open Frame Air Gap • Keep at least 10 mm between the panel and the enclosure protective glass to allow air to flow.
Enclosure Installation Guide FXING THE PANEL SCREW HOLES (Unit : mm) 117.6 117.6 41.6 1675.2 140.4 485.2 953.6 310.7 365.3 999.2 76.4 117.6 117.6 • Use the side screw holes when mounting the panel. • Remove the tape when using the side screw holes. •...
ENCLOSURE • Open the cable holder and pull out the cables. • Loosen the screws and remove the IR unit. • Install the IR unit in the enclosure in a distance where the cable can be reached. Cable IR Unit Safety and Precaution Guide for Installation Installing the Enclosure •...
REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully to use the monitor correctly. To install batteries, open the battery cover, place batteries (1.5 V AAA) matching terminals to the labels inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse.
Page 16
Selects the Picture Mode. (HOME) Activates the Launcher. Enters the White Balance menu. (SETTINGS) Accesses the main menus or saves your input and exit menus. This function is not supported. Navigation Buttons Scrolls through menus or options. Selects menus or options and confirms your input. (BACK) Allows you to move back one step in the user interaction function.
MAKING CONNECTIONS You can connect various external devices to your monitor. Change the input mode and select the external device you want to connect. For more information about external device connections, see the user manual provided with each device. Connecting to a PC Some of the cables are not provided.
Page 18
NOTE • For the best image quality, using the monitor with HDMI connection is recommended. • To comply with the standard specifications of the product, use a shielded interface cable with a ferrite core, such as a DVI-D cable. • If you turn the monitor on when the set is cold, the screen may flicker.
Connecting Multiple Monitors To use different products connected to each other, connect one end of the signal input cable (DP Cable) to the DP Out connector of Monitor 1 and connect the other end to the DP In connector of the other product. MONITOR 1 MONITOR 2 MONITOR 3...
TROUBLESHOOTING No image is displayed. Problem Action Is the product power cord connected? • Check if the power cord is correctly plugged into the power outlet. Does the “Invalid Format” message • The signal from the PC (Graphics card) is out of the vertical or appear? horizontal frequency range of the product.
Page 21
After-image appears on the product. Problem Action After-image appears when the product is • If you use a fixed image for a long time, the pixels may be damaged. turned off. Use the screen-saver function. • When a dark image is displayed on the screen after an image with high contrast (black and white or gray), this may cause image sticking.
Page 22
CAUTION • Image sticking does not occur when using constantly changing images but may occur when using a fixed image for an extended period of time. Therefore, it is recommended that you use the instructions below to decrease the likelihood of image sticking occurring when using a fixed image.
PRODUCT SPECIFICATIONS The product specifications below may be changed without prior notice due to upgrade of product functions. “ ” refers to alternating current (AC), and “ ” refers to direct current (DC). LCD screen Screen type Thin Film Transistor (TFT) Liquid Crystal Display (LCD) Screen Video signal Maximum resolution...
Page 24
75XF3ES LCD screen Pixel pitch 0.429 mm (H) X 0.429 mm (V) Power Rated power AC 100-240 V ~ 50/60 Hz 9.3 A Power consumption On Mode: 620 W (Typ.) Sleep Mode: ≤ 0.5 W Standby Mode: ≤ 0.5 W Environmental Operating Temperature 0 °C to 50 °C (without Direct Sunlight)
Page 25
HDMI/ DVI-D/ DisplayPort (PC) Support Mode Horizontal frequency Resolution Vertical frequency (Hz) (kHz) 800 x 600 37.879 60.317 1024 x 768 48.363 60.0 1280 x 720 44.772 59.855 1280 x 1024 63.981 60.02 1680 x 1050 65.290 59.954 1920 x 1080 67.5 3840 x 2160 67.5...
Page 26
Make sure to read the Safety Precautions before using the product. The model and serial numbers of the SET are located on the back and one side of the SET. Record it below should you ever need service. MODEL Temporary noise is normal when powering ON or OFF this device.
Need help?
Do you have a question about the 75XF3ES-B.AAU and is the answer not in the manual?
Questions and answers