Summary of Contents for Schiller CLASSEN TR-20H
- Page 1 MODELS: TR-20H / TR-20B / TR-20K TURF RAKE TR-20MH / TR-20MB TURF RAKE with MULTI-PURPOSE BLADE TR-20RH / TR-20RB TURF RAKE with SPRING TINE REEL TS-20H / TS-20B / TS-20K TURF SEEDER...
- Page 2 TURF RAKE/ SEEDER WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. www.p65warnings.ca.gov AVERTISSEMENT L’émission du moteur de ce matériel con-tient des produits chimiques que l’Etat de Californie considère être...
-
Page 3: Table Of Contents
You'll always be glad you did. CLASSEN ® SCHILLER GROUNDS CARE, INC. 1028 STREET ROAD, P.O. BOX 38 SOUTHAMPTON, PA 18966 PHONE 877-596-6337 • FAX 215-357-8045... -
Page 4: Safety
These words Grounds Care, Inc. Engineering Department. Any appear in this manual and on the safety labels Schiller Grounds Care, Inc. product that is altered, attached to Schiller Grounds Care, Inc. machines. modified or changed in any manner not specifically For your safety and the safety of others, read and authorized after original manufacture–including the... - Page 5 TURF RAKE/ SEEDER SAFETY Site Preparation and Circumstances Operator Preparation and Training – Evaluate the terrain to determine what accessories and attachments are needed to – Read the operation manual. properly and safely perform the job. – Read the engine manufacturer's owner manual. –...
- Page 6 TURF RAKE/ SEEDER SAFETY OPERATION SAFETY INTERRUPTING OPERATION – Before leaving the operator's position for GENERAL refueling, project end, or transport: – Use extra care when loading or unloading the a. Park on level ground machine onto a trailer or truck. Do not use split b.
- Page 7 TURF RAKE/ SEEDER SAFETY MAINTENANCE SAFETY OPERATING ON SLOPES GENERAL WARNING All slopes require extra caution. Loss-of-control and – Maintain machine according to manufacturer's tip-over accidents can lead to schedule and instructions for maximum safety severe injury or death. and best results. –...
- Page 8 TURF RAKE/ SEEDER SAFETY STORAGE SAFETY FUEL – Stop the engine and allow to cool before storing. WARNING – Drain the fuel tank outdoors only. – Store fuel in an approved container in a cool, dry place. – Use extra care when handling gasoline and –...
- Page 9 TURF RAKE/ SEEDER SAFETY DECALS WARNING Operation of This Equipment May Create Sparks That Can Start Fires Around Dry Vegetation. A Spark Arrestor May be Required. The Operator Should Contact Local Fire Agencies For Laws or Regulations Relating to Fire Prevention Requirements.
-
Page 10: Set-Up Instructions
TURF RAKE/ SEEDER SET-UP INSTRUCTIONS ASSEMBLY / SET UP INSTRUCTIONS NOTE: Units ship with no gas or oil. 1. READ THE OPERATOR'S MANUAL BEFORE ASSEMBLY. 2. Cut banding and roll rake off pallet. 3. Unfold by pulling up on handle. 4. -
Page 11: Operation
TURF RAKE/ SEEDER OPERATION FUELING STARTING THE ENGINE – Fill the fuel tank according to the engine Cold starts: manufacturer specifications. 1. Set the throttle lever to the half-open position. 2. Move the choke to the ON position. – Use a funnel to avoid spillage. Warm starts: 1. - Page 12 TURF RAKE/ SEEDER OPERATION OPTIONAL BLADE ASSEMBLIES Changing Complete Blade Assemblies BE CERTAIN THAT THE SET SCREWS ARE Within minutes your machine can be converted to a TIGHTENED PROPERLY IN BEARINGS AND turf rake, turf seeder or turf slicer by purchasing the PULLEY WHEN REASSEMBLING.
-
Page 13: Controls
TURF RAKE/ SEEDER CONTROLS FUEL SHUT OFF (A) RAKE BAIL (F) Move to the “OFF” Pull up on bottom bail to engage the main shaft. Release bail to disengage. position to shut off the fuel whenever transporting the machine by trailer, truck or during storage. Move to the HEIGHT ADJUSTMENT (G) “ON”... -
Page 14: Adjustments
TURF RAKE/ SEEDER ADJUSTMENTS Recommended Height Adjustments Seeding / Multipurpose Blade Assembly Height Raking Assembly Height The seeding/multipurpose blades are used for cutting grooves for over-seeding and can also be used When using the Turf Rake with its raking (flail) blade assembly adjust the raking height as follows. - Page 15 TURF RAKE/ SEEDER ADJUSTMENTS Slicer Blade Assembly Height The slicer blade assembly is recommended for slicing, verticutting or aerating when a thinner blade is preferred. This is the recommended blade for use on golf course greens. To set the height properly place unit on the lawn surface and adjust the wheel height up (see Fig.
-
Page 16: Maintenance/Storage
TURF RAKE/ SEEDER MAINTENANCE / STORAGE DAILY STORAGE INSTRUCTIONS Before the rake is put into storage for any period ex- • Perform daily maintenance checks to keep the turf ceeding 30 days, do the following: rake/seeder in good operating condition. 1. -
Page 17: Tire Scraper
TURF RAKE/ SEEDER TIRE SCRAPER TIRE SCRAPER INSTALLATION:... -
Page 18: Engine & Rake Assembly
TURF RAKE/ SEEDER ENGINE & RAKE ASSEMBLY 29 8... - Page 19 TURF RAKE/ SEEDER ENGINE & RAKE ASSEMBLY ITM PART NO. DESCRIPTION ITM PART NO. DESCRIPTION 4179011 S - RAKE DECK 4179012 S - SEEDER DECK 4173430.17 PLATE, END TR/TS C300012.17 PAD, ENGINE C100137 HONDA GX160 ENGINE C100051 B & S 550 SERIES ENGINE 102-0004-00 KOHLER CH245 ENGINE S-GUARD, BELT 4179013...
-
Page 20: Handle Assembly
TURF RAKE/ SEEDER HANDLE ASSEMBLY... - Page 21 TURF RAKE/ SEEDER HANDLE ASSEMBLY ITM PART NO. DESCRIPTION ITM PART NO. DESCRIPTION 4173268.17 LOWER HANDLE BRACE, LH 4173269.17 LOWER HANDLE BRACE,RH 4173278.17 HANDLE SUPPORT BRACKET 2 4171952.17 HANDLE ATTACHMENT BAR 4172558.17 HANDLE HOOK 4173270.17 MAIN HANDLE C500088 WASHER, 1/4" FLAT C500087 PIN, 3/32 X 1/2 COTTER C500118...
-
Page 22: Main Frame & Wheel Assembly
TURF RAKE/ SEEDER MAIN FRAME & WHEELS ASSEMBLY... - Page 23 TURF RAKE/ SEEDER MAIN FRAME & WHEELS ASSEMBLY ITM PART NO. DESCRIPTION ITM PART NO. DESCRIPTION 4179011 S - RAKE DECK 4179012 S - SEEDER DECK C100064 WHEEL ASSY, 8" FRONT C100063 WHEEL ASSY, 10" REAR C300015 DRAG SHIELD C300028 ROD, #10-24 THREADED C100069 DECAL, DANGER...
-
Page 24: Labels
TURF RAKE/ SEEDER LABELS WARNING Operation of This Equipment May Create Sparks That Can Start Fires Around Dry Vegetation. A Spark Arrestor May be Required. The Operator Should Contact Local Fire Agencies For Laws or Regulations Relating to Fire Prevention Requirements. --This label meets California 4442.6 100504... - Page 25 TURF RAKE/ SEEDER LABELS ITM PART NO. DESCRIPTION ITM PART NO. DESCRIPTION 4170316 DECAL, CLASSEN C100060 DECAL, CAUTION - MUFFLER/ SHIELDS 1 C100075 DECAL, TR-20 (TURF RAKE ONLY) C100071 DECAL,-BAIL ENGAGEMENT C100061 DECAL, CAUTION - OPERATING INST. C100077 DECAL, TS-20 (TURF SEEDER ONLY) C100069 DECAL, DANGER, HANDS/FEET WAY C100070...
-
Page 26: Seeder Box Assembly
TURF RAKE/ SEEDER SEEDER ASSEMBLY... - Page 27 TURF RAKE/ SEEDER SEEDER ASSEMBLY ITM PART NO. DESCRIPTION ITM PART NO. DESCRIPTION C400399.17 HOPPER WELDMENT C400400.17 SPREADER DRUM WELDMENT C400404.17 MAIN BODY LH CLOSURE PLATE C100355 WHEEL, 8” SEED BOX DRIVE C500029 BOLT, 1/4-20 x 3/4 C500136 NUT, 1/4-20 C400401.17 FLOW CONTROL C400406.17 FLOW CONTROL HANDLE WLDMNT C500088...
-
Page 28: Rake Blade Assembly
TURF RAKE/ SEEDER RAKE BLADE ASSEMBLY ITM PART NO. DESCRIPTION C700008 SHAFT, RAKE MAIN C300014 SHAFT, SATELLITE C300019 BLADE (FINGER), RAKE C100056 SPACER, FINGER C500078 E-CLIP, 1/2” C600014 MAIN SHAFT ASSEMBLY C900003 COMPLETE MAIN SHAFT ASSEMBLY 1 INCLUDES: END PLATES, BEARINGS, PULLEY, KEY &... -
Page 29: Multi-Purpose Assembly (Optional)
TURF RAKE/ SEEDER MULTI-PURPOSE BLADE ASSEMBLY OPTIONAL ITM PART NO. DESCRIPTION C700025 SHAFT W/ BLADE HOLDERS, C100310 BLADE W/ 5/16” HOLES, C500216 BOLT, 5/16-18 X 3/4 GRADE 8 C500217 NUT, 5/16-18 TOP LOCK C600030 SHAFT/BLADES SUB ASSY C900026 COMPLETE MULTIPURPOSE ASSY INCLUDES: END PLATES, BEARINGS, PULLEY, KEY &... -
Page 30: Slicer Assembly (Optional)
TURF RAKE/ SEEDER SLICER BLADE ASSEMBLY OPTIONAL ITM PART NO. DESCRIPTION C700025 SHAFT MULTIPURPOSE C100427 BLADE, SLICER SQUARE C500216 BOLT, 5/16-18 X 3/4 GRADE 8 C500217 NUT, 5/16-18 TOP LOCK C600040 SHAFT/BLADES SUB-ASSEMBLY C900027 COMPLETE MULTIPURPOSE ASSY INCLUDES SHAFT, BLADES, END PLATES, BEARINGS, PULLEY, KEY &... -
Page 31: Spring Tine Reel Assembly Optional
TURF RAKE/ SEEDER SPRING TINE REEL ASSEMBLY OPTIONAL ITM PART NO. DESCRIPTION C100620 E-CLIP 4171066 SPRING MNTNG ROD & REEL C100623 SPRING 4170956 ROD-SPRING MOUNTING C600064 SPRING TINE REEL ASSY (INCLUDES ITEMS 1-4) C900045 COMPLETE TINE REEL ASSEMBLY (INCLUDES ITEMS 5, 7-11) C100050 BEARING, FLANGE C100058... -
Page 32: Warranty
Operator’s Manual for the engine provided with your product or ask an authorized dealer for the terms and conditions of these warranties. Schiller Grounds Care makes no warranty with respect to other parts not of its manufacture such as tires, batteries, gearboxes, or similar. - Page 33 The authorized dealer makes no warranty of its own and such dealer has no authority to make any representation, warranty, or promise on behalf of Schiller Ground Care or to modify the terms or limitations of this limited warranty in any way.
Need help?
Do you have a question about the CLASSEN TR-20H and is the answer not in the manual?
Questions and answers