Rules For Safe Driving; Assistance Service - Polaris RANGER RZR 900 Use And Care Manual

RULES FOR SAFE DRIVING

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

ASSISTANCE SERVICE

offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
1 • Remove the chassis from the packaging and
position it on its side. Snap fit the teeth of the 2
red supports onto the chassis.
2 • Position the chassis horizontally and screw up
the 4 internal screws while holding the 2
supports in position.
3 • Push the 2 rear cylindrical shock absorbers into
the slots, ensuring that the sides are correct
(right and left are indicated on the back of the
items).
4 • Push the side trim section into the 2 slots in the
chassis. Fit the other trim section on the
opposite side.
5 • Fit the roll-bar support, first engaging the rear
section and then the front. Fit the other side in
the same way.
6 • Fix on the supports with the screws provided.
7 • Insert the roll bar into the supports, checking
that it is facing the right way, as shown in the
figure.
8 • Fix the roll bar using pressure to engage the 2
self-threading screws, one on each side.
9 • Apply the silver stickers in the 2 rear light seats.
10 • Push the rear lights into the respective seats.
11 • Position the seat as required (the seat can be
fitted in 2 positions) and fix it with the 2 screws
provided. Fit the other seat in the same way.
12 • Insert the 2 seatbelt buckles into the respective
central slots between the seats, as shown in the
figure.
13 • Fit the 2 ring clamps on the roll bar, one on each
side, opening them to position them correctly.
14 • Fix the 2 belts to the respective ring clamps with
the screws provided.
15 • Apply the speedometer sticker and push to fit
the transparent cover. Now fit the speedometer
to the dashboard, inserting first the tongue and
then the tooth.
16 • Snap fit the dashboard cover, inserting first the
upper teeth and then the lower, as shown in the
figure.
17 • Join the two sections of the steering wheel.
18 • Insert the horn into the central hole of the
steering wheel, following the instructions
included in its packaging.
19 • Remove the plastic protector from the steering
shaft. Fit the steering wheel on the steering
column, lining up the respective holes.
20 • On one side insert the screw and on one other
the nut, and fix the steering wheel as shown in
the figure.
21 • Push in the front roll bar until it is fully inserted
into the slots.
22 • Fix it with the 2 screws provided.
23 • Snap fit the 2 remaining front shock absorbers,
ensuring that the sides are correct (right and left
are indicated on the back of the items).
24 • Fit the front cover engaging it to the chassis at
the 6 points highlighted in detail A.
25 • Screw on the cover with the 2 screws provided.
26 • Apply the silvered stickers in the 2 front light
seats.
27 • Push the front lights into the respective seats.
28 • Remove the protective caps from the steering
levers. On one side, slide on one of the large
washers provided.
29 • Fit one of the two front wheels (the narrower
ones) on this same side. Keep the wheel trim on
the outside (check that it is fitted onto the
wheel and attach it to its pin if necessary). Next,
insert a small washer and then the nut. Tighten
the nut to secure the wheel. Use the same
procedure to fit the other front wheel.
30 • Remove the protective caps from the rear axle
and insert the axle into the rear of the vehicle as
shown in the figure.
31 • On one of the rear wheels, on the opposite side
to the rim, push on a driver. Now slide the wheel
onto the axle, and keep it in position while fitting
the other rear wheel in the same way.
32 • Fit a small washer and nut on both wheels.
Tighten the nuts using the spanner provided on
one side and a pair of pliers on the other.
33 • Snap fit the 4 wheel hubcaps.
CONSUMER
34 • Open the battery compartment by rotating the
red catch to the lock open position. Connect the
electrical system plug with the battery plug.
ASSEMBLY
35 • Close the battery compartment by inserting the
cover at the front below the cover plate.
Complete the operation by inserting the red
catch and rotating it 180º using a coin. The
vehicle is now ready for use.
FEATURES AND INSTRUCTIONS FOR USE
36 • A: HORN. Press the yellow button to sound the
horn.
B: Passenger HANDRAIL.
C: Electrical accelerator and brake pedal. The
brake activates automatically when the
accelerator is released.
37 • To release the seat belt: 1 pull towards the
centre while pushing the button; 2 disengage.
38 • Rear DRINKS HOLDER. There is a double drinks
holder in the rear box.
39 • ADJUSTABLE SEATS. The seats can be adjusted
in 2 positions as the child grows, as shown in the
figure.
40 • GEAR LEVER: when supplied the vehicle speed is
limited to first gear (1 - see figure). It also has a
reverse (R), and a second gear (2) recommended
only for expert drivers. To enable the second
gear, unscrew the red stop on the gear lever.
41 • Rotate the stop 90°, as shown in the figure, and
fix in position with the screw. Now by pulling
back the gear lever the vehicle can run in second
gear.
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
42 • Use a coin to open the battery compartment.
Disconnect the battery from the system. Remove
the 2 screws from the battery holder in the
compartment.
43 • Replace the flat battery. Put the battery holder
back in place and secure it with the screws.
Connect the two plugs, close the battery
compartment and fasten it shut.
BATTERY CHARGING
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
44 • Disconnect plug A of the electrical system from
plug B of the battery by pressing laterally.
45 • Connect the battery charger to a domestic
power outlet according to the instructions
included with the charger. Connect plug B with
plug C of the battery charger.
46 • When charging is complete, disconnect the
battery charger from the power outlet and then
disconnect plug C from plug B.
47 • Fully insert plug B into plug A, until it snaps into
position. At the end of charging operations
always remember to insert and fix the battery
holder. Close the battery compartment and
secure it with the catch.