GasLab RAD-0102-6 Manual
  1. Manuals
  2. Brands
  3. GasLab Manuals
  4. Security System
  5. RAD-0102-6
  6. Manual

GasLab RAD-0102-6 Manual

Co2 storage safety alarm
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
 
CO2 Storage Safety Alarm 
RAD‐0102‐6 
 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RAD-0102-6 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for GasLab RAD-0102-6

Summary of Contents for GasLab RAD-0102-6

  • Page 1   CO2 Storage Safety Alarm  RAD‐0102‐6   ...

  • Page 2: Product Overview

    These standards meet IFC, NFPA, and NBIC requirements for monitoring. RAD-0102-6 CO2 Monitor is cost-effective and includes these features: 1.) Multiple RDU’s can be connected for additional alarm points. 2.) Large digital LCD display clearly indicates the ambient CO2 concentration, relative humidity, and temperature.
  • Page 3 SEU (Main Sensor Unit) A. CO2 Sensor B. LCD display C. Power (Green LED) D. AL1 (Red 1 LED) E. AL2 (Red 2 LED) F. AL3 (Red 3 LED) G. Fault (Yellow LED) H. Mode Button I. UP Button J. Down Button K.
  • Page 4 3. LCD Display Symbol Symbol Meaning Description Concentrati on ppm Ambient CO2 Concentration (Parts Per Million) Alarm Alarm Icon Test communications between DIAG Diagnose the SEU and RDU (see 9.1) Relay 1 will trigger when CO2 concentration exceeds 5000ppm TWA (Time CO2 5,000 Weighted Average).
  • Page 5 When the CO2 TWA value drops below 5000ppm (with 5% hysteresis), AL1 (Red1 LED) will stop blinking and Relay 1 will be inactive. When the RAD-0102-6 detects a CO2 value that exceeds the AL2 CO2 level, AL2 (Red 2 LED) will blink, the buzzer will sound and Relay 2 will be triggered.

  • Page 6: Installation Instructions

    Plug the CAT5 cable into the designated ports. Communication between the SEU and RDU is complete. 5. The RAD-0102-6 has 3 relay outputs connected to the programmed alarm settings. All relays are normally open/closed dry contacts. Any of the relays can be used to control an external device (fan, HVAC system, etc.) or can be wired to the fire alarm panel directly.
  • Page 7 9. Advanced Management Settings 9.1) Latch function: On/Off. Default is On. Fault light will keep flashing if AL3 is activated, indicating unit went into alarm status. 1. Press Up & Enter button for 10 seconds 2. Change to Advance Mode by pressing Mode, and choose Lat Mode 3.

  • Page 8: Customizing The Settings

    10. Customizing the Settings When power has been connected, all LEDs will flash and buzzer will beep 4 times, at this time, the LCD will show all icons for about 4 seconds. After that, the SEU and RDU will begin to monitor the CO2 concentration. In order to the get timely alarm safety information and meet the personal requirements, it is advisable to set up the customizing parameter.
  • Page 9 10.3) Setting the AL2 – 2 CO2 Alarm Level parameter: User configurable 1. Press Mode until the “AL2” & “CO2” icons flash 2. Press Enter, the “AL2” icon shows on LCD, default AL2= 1.5% 3. Press Up/Down to go through “5000,1.0%,1.5%,2.0%,2.5%,3.0%” alarm level. 4.
  • Page 10 10.5) Calibration using the CO2 CALI function: 1. You will need a gas cylinder of pure Nitrogen (0 ppm CO2). 2. Temporarily cover the buzzer hole on the bottom left-hand corner of the SEU (Main unit) and bottom right-hand corner on the RDU (remote display unit) with a small piece of masking tape to minimize the alarm sound during calibration.

  • Page 11: Safety Notice

    10.6) Using the Recover factory setting function: Note: If the user has set the customer parameters or calibrates the RAD-0102-6 incorrectly, please use the ReFactSet (recover the factory Setting) to recover the default factory setting 1. Press Mode until the “ReFactSet” icon flashes.

  • Page 12: Specifications

    6.69 x 4.96 x 2.73 inches Weight 0.4 lb Dimensions (LxWxD) 5.51 x 3.54 x 1.89 inches 14. Fault Codes &Troubleshooting Guide This section includes a list of Frequently Asked Questions for problems you may encounter with the RAD-0102-6 CO2 Monitor.

  • Page 13: Support And Warranty

    This meter comes with a one (1) year warranty starting from the date it was shipped to the buyer. For more information visit our website: https://GasLab.com/pages/terms-conditions For information or technical support, please contact us. support@gaslab.com (386) 872-7668 www.GasLab.com GasLab, Inc. 131 Business Center Dr STE 3 Ormond Beach, FL 32174 USA Ref. No.:062017...

Table of Contents