Hatco B950 Installation Manual

Hatco / ADM Sneezeguards
Self-Service Sneeze Guards
Model B950
Model B950 Self-Service Sneeze Guards are available in ten
widths ranging from 36"–144" (914–3658 mm), with a common
depth of 18" (457 mm). All of the available widths are height
adjustable from 9"–19" (229–483 mm) to the bottom edge of the
rotating glass face panel (with the glass set at 45° angle).
For additional information regarding Model B950, scan the QR
Code below:
https://www.hatcocorp.com/en/equipment/sneeze-guard-equipment/
self-service/flav-r-shield-adjustable-self-service-sneeze-guard-b950
Important Safety Information
To avoid injury and damage to equipment or property, read the
following safety information before installing this equipment.
Do not attempt to assemble and install sneeze guards
alone. Installation of sneeze guards requires two or
more people, dependent upon unit.
Always wear proper protective eye wear when handling
glass sneeze guards.
Never spray cleaners directly onto sneeze guard
surfaces. Spray cleaner into non-abrasive cloth, and then
wipe down surfaces.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit,
marring its appearance and making it susceptible to
soil accumulation. Use of abrasive materials will void
warranty.
Assembly and Installation
1. Unpack all components. Verify that the appropriate number of
the items below are present.
• Face Panel, 3/8" Tempered Glass
• End Panel, 3/8" Tempered Glass (optional)
• Adjustable Post Assembly w/Bracket
(1-1/2" Base Tube w/1" Adjustable Tube)
• Adjustable Center Post Assembly w/Brackets
(1-1/2" Base Tube w/1" Adjustable Tube—multiple bay only)
• Hardware Packet (includes hex wrenches for set screws)
2. Remove the flange cup and washer
from each post assembly.
a. Using the included hex wrench,
loosen the set screw on the cup.
b. Slide the cup off of the post assembly.
The washer is inside the cup.
3. Install the flange cups to the mounting
surface.
a. Refer to the "Model B950 Standard Sizes" chart and illustration
to determine the location of the flange cups. For multiple bay
installations, refer to "Width per Bay" column in the chart.
IMPORTANT NOTE
Sneeze guards that consist of multiple bays require careful
measurement before installation of the flange cups.
b. Determine how to install the flange cups.
They can be installed using a single lag
bolt with the included washer through
the center hole, or three #8 or #10
countersunk-style fasteners appropriate
for the mounting surface.
© 2023 Hatco Corporation
c. Position the flange cups in the appropriate locations, and
mark the screw hole locations. IMPORTANT! Measure
carefully, and make sure the cups remain square to each
other as well as the installation location.
d. Pre-drill the screw holes in the mounting surface.
Model B950 Standard Sizes
Item Number
B950-36
B950-48
B950-60
B950-72
B950-084
B950-096
B950-108
B950-120
B950-132
B950-144
B950-36 (1 Bay)
B950-60 (2 Bay)
Post
Assembly
Washer
Flange
Cup
Orbit
Bracket
Set
Screw
4. Insert each post assembly into its corresponding flange cup.
Make sure the posts are fully seated in the cups.
5. Tighten the set screw on each flange cup securely.
Countersunk
Hole
Cup
Top
View
Center Hole
1
P/N 07.14.011.00-0423 [B950_IG]
INSTALLATION GUIDE
Total Width (A) Number
(post center to of
center) Bays
36"
1
(914 mm)
48"
2
(1219 mm)
60"
2
(1524 mm)
72"
2
(1829 mm)
84"
2
(2134 mm)
96"
3
(2438 mm)
108"
3
(2743 mm)
120"
3
(3048 mm)
132"
4
(3353 mm)
144"
4
(3658 mm)
9"
to
19"
A
Adjustable
Center Post
Assembly
B B
A
Width per Bay (B)
(post center to
center)
36"
(914 mm)
24"
(610 mm)
30"
(762 mm)
36"
(914 mm)
42"
(1067 mm)
32"
(813 mm)
36"
(914 mm)
40"
(1016 mm)
33"
(838 mm)
36"
(914 mm)
45º
20"
Angle
19" 19"
End Panel End Panel
Clip Clip
18"
Up to 23"
...continued