Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tool Shed TSWB2
Summary of Contents for Tool Shed TSWB2
- Page 1 WATER BLASTER 2300W TSWB2 www.thetoolshed.co.nz...
-
Page 2: Product Details
OPERATION MANUAL PRODUCT DETAILS PRODUCT Water Blaster 2300W MODEL NO. TSWB2 ISTRIBUTED BY NOTE: This manual is only for your reference. Due to the continuous improvement of the ToolShed products, changes may be made at any time without obligation or notice. -
Page 3: Table Of Contents
OPERATION MANUAL C O N T E N T S: Product Details ............................2 Specifications ............................4 Identification ............................4 Safety Information ..........................5 Assembly ..............................7 Operation ..............................9 Cleaning & Storage ..........................11 Cleaning Tips ............................12 Troubleshooting ........................... 13 www.thetoolshed.co.nz... -
Page 4: Specifications
OPERATION MANUAL SPECIFICATIONS Water Pressure 1900 PSI Litres Per Minute Weight 21kg Motor 2200W Induction Product Size 881mm x 355mm x 407mm Carton Size 905mm x 370mm x 390mm IDENTIFICATION Quick Connector Power Cable Hook Filter Hose Reel w/ Hose High Pressure Hose Gun Holder High Pressure Hose Clip... -
Page 5: Safety Information
OPERATION MANUAL IMPORTANT SAFETY INFORMATION NEVER point the high-pressure nozzle at people or animals. NEVER drink alcohol or use drugs while operating the pressure cleaner. NEVER operate the pressure cleaner while standing in water. NEVER touch the electrical plug with wet hands. NEVER let electrical connections rest in water. - Page 6 OPERATION MANUAL Do not leave the pressure cleaner unattended while the power switch is ON. Keep water spray away from electrical wiring or it may result in electric shock. PROPER USE OF THE PRESSURE CLEANER Operate the pressure cleaner at no more than the fluid pressure rated for the pressure cleaner.
-
Page 7: Assembly
OPERATION MANUAL ASSEMBLY 1. Attach the high-pressure hose (C) to the gun (H). Insert and quick-connect it tight to avoid leakage. When the pieces are joined properly, you cannot separate the two components by pulling straight out from the gun (H). Push the hose lock button, then you can pull out the high-pressure hose. - Page 8 OPERATION MANUAL 4. Insert the adjustable spray nozzle (J) into the gun (H). Push and turn the adjustable nozzle (J) clockwise onto the gun (H) until it is hand tight to lock it into place. When the pieces are joined properly, you cannot separate the two components by pulling straight out on the adjustable nozzle.
-
Page 9: Operation
OPERATION MANUAL OPERATION This unit is intended to be used with cold water only. Do not use hot water in this pressure cleaner. Starting Up After connecting the pressure cleaner to your cold-water supply, proceed as follows: 1. Open the water supply valve completely. 2. - Page 10 OPERATION MANUAL Adjustable Spray Nozzle The adjustable nozzle will allow you to use any variety of spray patterns from a full fan spray to a direct stream spray. When using the pressure washer to clean wood decks, siding, vehicles, etc., always start using the fan spray and begin spraying from a minimum 36”...
-
Page 11: Cleaning & Storage
OPERATION MANUAL CLEAN UP & STORAGE When finished using the pressure cleaner, follow these steps to shut down the unit: 1. Turn the pressure cleaner to the OFF position. 2. Turn off the water supply. 3. Before disconnecting the high-pressure hose connection, point the gun in a safe direction and discharge the high-pressure water. -
Page 12: Cleaning Tips
OPERATION MANUAL CLEANING TIPS WARNING: Always test the spray in an area free and clear of people and objects before you spray at the intended cleaning surface. Wood & Vinyl Decks Rinse the deck and surrounding area with fresh water. If using detergent, fill the detergent reservoir and apply to the area being cleaned at low pressure. -
Page 13: Troubleshooting
OPERATION MANUAL TROUBLESHOOTING Problem Probable Cause Solution When the switch is in the ‘I’ Electrical socket is faulty. Check plug, socket, and fuses. position, the machine will not Voltage is inadequate. Check voltage. start. Washer is not plugged in. Plug in the power cord. Water inlet filter is clogged.
Need help?
Do you have a question about the TSWB2 and is the answer not in the manual?
Questions and answers