PacLights FFHS/2 Series Installation Sheet

FF HS/2 Series LED lood Light
STANDARD INSTALLATION STEPS
1
Each FFHS/2 Luminaire includes a Trunnion Mount. The Trunnion Mount can be
adjusted to a desired tilt angle for all the FFHS/2 Series. The FFHS/2-600/750/1000
/1200 have a lever on each side along with larger side brackets to support the heavy
fixture.
FFHS/2-400/500
Center Bolt
Arc Slot Bolt
2
The FFHS/2 Luminaires can be adjusted by using a wrench to loosen the center
bolts and the arc slot bolts located on the sides of the FFHS/2 Luminaire. The
FFHS/2-600/750/1000/1200 Luminaires will also need the lever bolts located on the
sides of the FFHS/2 Luminaire to be loosened. The fixture will now be able to rotate
to the desired tilt/angle. Replace the arc slot bolts and tighten all the other bolts.
Using a J-Box, Connect the ACL and the ACN from the J-Box to the Fixture with the AC Power Supply
cords. Follow the Wiring Diagram provided.
DIM
AC Power Supply
NEUTRAL [WHITE]
G ROUND [
Need help? Tech help line: (800) 988-6386 Email: cs@paclights.com Website: www.paclights.com
Copyright © 2021 PacLights
F
Installation Sheet
FFHS/2-600/750/1000/1200
Lever Bolt
Lever
Center Bolt
Arc Slot Bolt
Lever Bolt
FFHS/2 J-Box
Optional Dim Connector
GRAY (-)
Violet (+)
HOT [BLACK]
Main Wire
Connector
GREEN ]
All Rights Reserved
Includes: FFHS/2-400, FFHS/2-500, FFHS/2-600, FFHS/2-750,
FFHS/2-1000, FFHS/2-1200
CAUTION:
PLEASE FOLLOW THIS INSTRUCTION MANUAL CAREFULLY TO
PREVENT ANY INJURIES OR COMPLICATIONS THAT MAY ARISE.
WARNING:
Before installing or maintaining the luminary, make sure all powers are
TURNED OFF .
Verify that supply voltage is correct by comparing it with the label information on all
fixtures.
Make all connections in accordance with the NEC requirements, and make sure all
luminaries are properly secured to prevent any wire complications. This luminary is
to always be installed with the lens facing down and its not to exceed the maximum
ambient temperature rating noted on the specification sheet.
3
FFHS/2-400/500 and FFHS/2-600/750/1000/1200 Luminaires have Trunnion
Mount bolt hole dimensions as seen below. Please use the Trunnion Mount
dimensions below to determine the drilling template to follow if the fixture is going
to be surface mounted with the Trunnion Mount.
FFHS/2-400/500
Ø0.62"
0.62"
6.50"
8.00"
Surge Protector
Each FFHS/2 Series fixture is provided with a Junction Box that contains wire
Connectors and a Surge Protector. The Surge Protector is required! The Surge
Protector is pre-installed, fastened with a screw inside the Junction Box. Please follow
the wiring diagram below.
Connector
G ROUND [
CAUTION:
PLEASE INCLUDE THE JUNCTION BOX PROVIDED.
WARNING:
Junction Box contains a necessary Surge Protector.
ACL [BLACK]
ACN [WHITE]
G ROUND [ GREEN ]
Surge Protector
Note: Instructions are subject to change at any time without notice
FFHS/2-600/750/1000/1200
0.64"
7.75"
9.50"
ACL [BLACK]
ACN [WHITE]
GREEN ]
Surge Protector
DIM
GRAY (-)
Violet (+)
TO FIXTURE
ACL [ BROWN /BLACK]
ACN [ BLUE /WHITE]
G ROUND [ GREEN ]
02-00036-211214
Ø0.64
Screw
Hole
Page 1 of 2