Advertisement
USER GUIDE
2.
Remove corresponding screws on opposite side of
cabinet. On some models there may be a nut behind
Remove bottom hinge:
one or both screws on either side.
1.
Remove bottom hinge from cabinet using a T-25 TORX
Install bottom hinge:
screw driver to remove three screws.
Install two or three screws, depending on model. Replace
nuts if used.
2.
Remove corresponding screws on opposite side of
cabinet. On some models there may be a nut behind
one or both screws on either side.
Install bottom hinge:
Note: It is necessary to remove and switch the
Install two or three screws, depending on model. Replace
wine rack mounting hardware. This will allow the
Door Adjustments
Note: It is necessary to remove and switch the
nuts if used.
racks to extend out of the unit beyond the door.
shelf-mounting hardware. This will allow the
shelf to extend out of the unit beyond the door.
Remove a wine rack:
Remove bottom shelf:
1.
Pull out rack as far as it will go.
1.
Pull out shelf as far as it will go.
2.
Locate the tabs inside the right and left slides.
2.
Locate the tabs inside the right and left shelf slides.
3.
Push down on the tab on the right and pull slightly on
3.
Push down on the tab on the right and pull slightly on
the rack to allow it to pass beyond the lock.
the shelf to allow it to pass beyond the lock.
4.
While holding the rack so it does not re-lock on the
4.
While holding the shelf so it does not re-lock on the
right, lift up on the left-side tab, and pull the rack
right, lift up on the left-side tab, and pull the shelf
toward you until it is completely free from the unit
toward you until it is completely free from the unit.
Door Adjustments
Pull tab
up
Spacer
Install slide spacers on opposite sidewalls:
Door Adjustments
1.
Take out 4 screws and remove the two brackets and
spacers from the sidewalls of the unit - leave the
u-line.com
Push tab
down
Spacer
Spacer
USER GUIDE
3.
Remove door by tilting forward and lifting door off
bottom hinge. Retain shoulder washers; they will be
Install slide spacers on opposite sidewalls:
reused.
4.
Insert arrow clips into holes.
1.
Take out 4 screws and remove the two brackets and
spacers from the sidewalls of the unit - leave the
screws in the brackets and spacers to keep them
together.
2.
Rotate door 180
and set on bottom hinge.
o
2.
Using 4 screws, install the spacers and brackets on
the opposite sidewalls - the open ends of the brackets
3.
Align edge of the hinge with the outer edge of the
need to remain toward the front of the unit.
unit.
Remove bottom hinge:
Note: Be sure that the hinge side of the unit has
1.
Remove bottom hinge from cabinet using a T-25 TORX
4.
Tighten three hinge screws using a Torx T-25
the slide bracket with the thicker spacer.
screw driver to remove three screws.
screwdriver.
Non-hinge Side
5.
Replace hinge cover.
Align and adjust the door:
+
Align and adjust the door (see DOOR ALIGNMENT AND
Open end of bracket
ADJUSTMENT)
Hinge Side
Install grille and hinge cover
Back of Unit
2.
Remove corresponding screws on opposite side of
cabinet. On some models there may be a nut behind
3.
Line up rack slide with slide brackets and push rack in
one or both screws on either side.
all the way. Pull rack outward all the way to make sure
Install bottom hinge:
locks are engaged.
Install two or three screws, depending on model. Replace
nuts if used.
Install bottom hinge and door:
Install two or three screws,
depending on model. Replace
nuts if used.
Install top hinge and door:
1.
Install hinge with longer straight edge aligned to
Door Adjustments
outside edge of cabinet. Do not tighten.
2.
Rotate door 180
and
o
set on bottom hinge.
3.
Align edge of the
hinge with the outer
edge of the unit.
4.
Tighten three hinge
screws.
Align and adjust the door:
Align and adjust the door (see DOOR ALIGNMENT AND
ADJUSTMENT)
Install grille and hinge cover
18
Back of Unit
+
Thicker end
of spacer
Open end of bracket
Advertisement
