Advertisement
Before activating the trigger, GRIP the gun firmly to counteract the recoil from the high pressure water jet.
"
WARNING! Avoid sudden bursts of water as these will cause water pressure to drop and put extreme pressure on hoses and connectors.
F
If, during operation, power failure occurs turn the electricity and water off for safety reasons, (See Note ‘c’ at end of Section 4).
"
WARNING! The high pressure jet will cause loose particles to be propelled at high speed, which may cause serious injury.
F
WARNING! DO NOT operate the machine without a water supply. Dry running can seriously damage the unit.
F
WARNING! DO NOT leave the washer switched on for more than 15 minutes without operating the trigger.
F
DO NOT obstruct ventilation grills during operation.
&
DO NOT use the washer with flammable or toxic liquids or any other product. Use only recommended detergent. Unapproved
&
detergents may corrode the machine cover and accessories.
DO NOT jam the trigger in the operating position.
&
DO NOT adjust any internal control valves, as they have been factory set.
&
DO NOT connect other appliances to the machine inlet or outlet.
&
DO NOT use in damp or wet weather conditions.
&
DO NOT move the unit by pulling the hoses or electrical cables. Use the handle.
&
DO NOT touch plug with wet hands. To avoid the risk of electrocution keep all connections dry and off the ground.
&
DO NOT direct jet against yourself, other persons, animals, electrical equipment or the machine itself.
&
DO NOT use washer if you are tired or under the influence of alcohol, drugs or intoxicating medication.
&
DO NOT allow children or untrained persons to operate the washer.
&
WARNING! Discharge residual pressure before disconnecting the washer hose. Pressure left in unit may cause injury.
F
After use, disconnect washer from electrical mains and water supply and store in a safe, dry, childproof area.
"
2.
SPECIFICATIONS & CONTENT
By rotating the stream of water at high speed, it is possible to increase the effective cleaning pressure of washer. We quote the pressure at
which the water leaves the pump as ‘Manifold Pressure’ and express the cleaning power of the washer as the ‘Effective Cleaning Pressure’.
2.1. SPECIFICATIONS
Lance 1 . . . . . . . . . . . . . . .Rotating Nozzle . . .Rotating Nozzle
Lance 2 . . . . . . . . . . . . . . . . .Fixed Nozzle . . . . .Fixed Nozzle
Manifold Pressure . . . . . . . . . . . . .1850psi . . . . . . . . .2000psi
Effective Cleaning Pressure . . . . . .3150psi . . . . . . . . .3450psi
Water Flow
. . . . . . . . . . . . . . . . .430ltr/hr . . . . . . . .440ltr/hr
Motor Power . . . . . . . . . . . . . . . . . .1800W . . . . . . . . .2300W
2.2.
CONTENTS
Unpack the product and check contents against the list below. Also check that the machine has an identification plate or label. If label or parts
are damaged or missing contact your supplier immediately.
DESCRIPTION OF ITEMS
A
Detergent bottle with flow control
B
Handle
C
Gun with safety catch
D
Rotary lance
E
Fixed lance
F
Water inlet with filter
G
Nozzle cleaning tool
3.
SET-UP
F
WARNING! Ensure that the pressure washer is switched off and unplugged from the mains power supply before proceeding.
3.1.
Slot handle, fig. 1.B, into body of washer, as shown in fig. 2.
3.2.
To connect lance D or E to the gun C, push the lance into the end of the gun and twist to lock as in fig. 3.
3.3.
Connect the high pressure hose K to the gun C and lock in place, as shown in fig. 4.
3.4.
Connect the high pressure hose K to the washer outlet H, as shown in fig. 5.
3.5.
Connect the mains water supply hose (not supplied) to the water inlet F on the pressure washer. DO NOT turn on the water at this stage.
The supply hose must be reinforced, and have an internal diameter of 1/2”. The water
supply must be at least equal to the washer output. The water temperature must NOT
exceed 122
F (50
C). The water supply pressure must NOT exceed 145psi (10 bar).
O
O
F
WARNING! REMINDER: The pressure washer must only be used with clean water.
Unfiltered water or corrosive chemicals must not be used as these will damage the washer.
3.6.
Check that the motor switch I is in the ‘Off’ position.
3.7.
Having carefully followed the safety instructions in Section 1, plug the washer into the mains
power supply. The washer is now ready for use as described in Section 4.
fig. 3
PC3150
PC3450
H
Water outlet
I
Motor switch
J
Instruction manual
K
High pressure hose
Input Voltage/Current...................230V/7.8A . . . . . . . 230V/10A
Motor Speed...................................2800rpm . . . . . . . . 2800rpm
Max. Inlet Temp. ...................................50
Hose Length .......................................5.5mtr . . . . . . . . . . 5.5mtr
Weight...................................................17kg . . . . . . . . . . . 17kg
fig. 5
fig. 4
PC3150
PC3450
C . . . . . . . . . . . 50
C
O
O
fig. 1
fig. 2
PC3150, PC3450 - 2 - 090502
Advertisement
