Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Altech SL-2401
Summary of Contents for Altech SL-2401
- Page 1 SL-2401B / S...
-
Page 2: Table Of Contents
CONTENTS Technical specification & feature-----------------------------------------------3 Part list ----------------------------------------------------------------------------------3 Motor structure diagram-----------------------------------------------------------4 Typical installation layout---------------------------------------------------------5 Factory setting motor open direction-----------------------------------------6 General safety ------------------------------------------------------------------6 Installation of the opener-----------------------------------------------------8 Necessary tools----------------------------------------------------------------8 Caution --------------------------------------------------------------------------8 Example sliding gate setup -------------------------------------------------9 Installation procedures ------------------------------------------------------9 Manual operation -------------------------------------------------------------------10 Installation of the gear rack -----------------------------------------------------10 Installation of limit magnet ------------------------------------------------------10 Control board program -----------------------------------------------------------11... -
Page 3: Technical Specification & Feature
Technical Specifications & Features Specifications: Power supply: Model B: 220V±10%, 50/60Hz Model S: Solar Power Panel 24v 30w Motor: 24VDC Absorbed motor power: 200W Gate moving speed: 15m/min Max gate weight: 1000KGS Environmental conditions: From -25°C to +50°C Protection class: IP44 ... -
Page 4: Motor Structure Diagram
Model S with solar power charge controller: 2*remote control 1* sliding gate motor 2*manual release key 2* magnet 1*lithium battery 4*expansion bolt Motor structure diagram Model B with lead acid battery:... -
Page 5: Typical Installation Layout
Model S with solar power charge controller: Typical installation layou Fig 5 Noted: Before Installing, test the motor by plugging it into a power and pressing the remote. You will see the motor cog turn. When it stops (after approx 1 minute), press the remote again to see it turn in the opposite direction. -
Page 6: Factory Setting Motor Open Direction
Factory setting motor open direction: The gate motor will open the gate to the right-hand side as its default setting ,as below picture(Fig 6): Fig 6 Gate in closed position Gate in open position If gate need to open to the left-hand , then motor need to be installed on the left side of gate, as below picture(Fig 7) showed,now you will need do below procedures: 1.Exchange motor open and close cable on the control board motor connection terminal 2.Swap over two magnets positions... - Page 7 • This product was exclusively designed and manufactured for the use specified in the present documentation. Any other use not specified in this documentation could damage the product and be dangerous. • The factory declines all responsibility for any consequences resulting from improper use of the product, or use which is different from that expected and specified in the present documentation.
-
Page 8: Installation Of The Opener
• Anything which is not expressly provided for in the present instructions is not allowed. • Installation must be carried out using the safety devices and controls prescribed by the EN 12978 standard. Fig 9 Installation of the Opener Necessary Tools ... -
Page 9: Example Sliding Gate Setup
Example Sliding Gate Setup(Fig 11) Fig 11 Note:Before motor installation , sliding gate must installed well with hardware kit .If any gate hardware kit require, please contact with us. Installation procedures (Fig 12) 1.The limit default setting is for gate in close position. Before installation, please make sure gate is closed. 2. -
Page 10: Manual Operation
Manual Operation The opener comes with an easy operating manual release. It brings the easiest manual release operation just in case of any emergency. Insert the manual release key supplied in package to release lock, then turning the key clockwise 90 degrees. ... -
Page 11: Control Board Program
position of the opener and/or place a few shims between the rack and gate. 2. Manually slide the gate leaf to ensure the rack is properly installed on the gear of the gate opener. 3. The gear rack length must be longer than the actual travel distance of the gate. Cut away any excess gear rack not needed. -
Page 12: Push Button Connection
2.COM terminal: use for connect COM terminal or GND 3.Open terminal: use for connect device that want open gate 4.Close terminal: use for connect device that want close gate 5.Start terminal: Single button control mode switch, used for controlling gate“open-close-stop-open-close” cyclically (Fig 18) (Fig 18) Example for push button;... -
Page 13: Flashing Light Connection
Connect terminal ⑧ to the “- “of photocell RX and TX. 8.COM terminal: use for connect COM terminal or GND 9.VCC terminal: on board power supply for infrared external device etc. 10.COM terminal: use for connect COM terminal or GND 11. -
Page 14: Motor Connection
B. Install the motor on the left of gate. (Fig 22) When the motor being installed to left of gate , motor wire diagram as picture shows， Terminal ⑫ connect the black wire from motor Terminal ⑬ connect the green wire from motor 14&15. -
Page 15: Battery And Solar Connection
16&17 Power terminal: use for battery and solar system load. A. Battery connect as below (Fig 23) B.Detail solar system connect method as below: (Fig 24) Function details: After control panel power on, the status indicator LED lit up. Status Indicator LED Blue indicator LED lit up means gate opening. - Page 16 Press and hold LEARN button 5s until buzzer with long beep then release button, digital Code clearing LED will show “00”. After code clearing, all remotes will be unpaired. 1. Press LEARN button, instruction LED light on, then press remote button, with buzzer short beep, then means code learning successfully, digital LED will show the quantity that remote learned 2.
-
Page 17: Digital Display Setting
Intelligent charging function 1. When the battery voltage is less than 25V ± 1, the charging function will be started automatically. 2. When the battery is fully charged, the charging circuit is automatically disconnected to Intelligent charging prevent overcharging. function 3. -
Page 18: Board Digital Led Display
Factory set: 0 Limit mode option 0： NC mode 1： NO mode Factory: 0 Single button control mode 0：close 1：open Factory set: 0 Lamp control mode: Mode 0: when gate moving, lamp light on; after gate stop 30s, lamp off; 0: Mode 0 Mode 1: when gate moving, lamp light on;...
Need help?
Do you have a question about the SL-2401 and is the answer not in the manual?
Questions and answers