Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for LARDIS LARDIS:ONE LAR-1192
- Page 1 Installation Guide LAR-1192 LARDIS:ONE (LAR-1192)
-
Page 2: Safety Information
Avoid prolonged exposure to sunlight. Use only accessories approved by the manufacturer to avoid damage to the product with possible loss of warranty. The permissible ambient temperature is -10°C to +60°C. LARDIS LAR-1192 Page 2 of 22 RTM:IT 2022-11-30... -
Page 3: Intended Application
2 Intended Application LARDIS:ONE is a car touch control panel with a 7-inch screen for radio control and navigation, for use in a closed vehicle interior. The product is aimed at I&C personnel in the area of authorities and organizations with security tasks. -
Page 4: Package Contents
[E] Connection adapter for Sepura SRG PEI [F] OTG connection adapter for USB accessories [G] Connection adapter for rear view camera [H] USB-C cable for configuration and update of the software ler! elle ler! elle LARDIS LAR-1192 Page 4 of 22 RTM:IT 2022-11-30... -
Page 5: Optional Accessories
Level converter with GPIO button adapter for connection of up to three LAR-1163 + potential-free make contacts LAR-1164 (both connection lines are required for connection) LARDIS:ONE connection kit (contains items [B], Fehler! Verweisquelle konnte LAR-1211 nicht gefunden werden., [D], [E], [F] and [G]) LARDIS LAR-1192 Page 5 of 22... -
Page 6: Cable Lengths
5 Cable Lengths Cradle LARDIS ONE 20 cm 140 cm 18 cm 58 cm 200 cm 16 cm LARDIS LAR-1192 Page 6 of 22 RTM:IT 2022-11-30... -
Page 7: Power Supply Connection
After switching on this control line again, the display is switched on again. Ground +12V / +24V Ignition terminal 31 terminal 30 terminal 15 The on-board power supply line for the control panel must be protected by an external 3- amp fuse. LARDIS LAR-1192 Page 7 of 22 RTM:IT 2022-11-30... - Page 8 Connect the cradle [B] to the radio connection cable [D] and the PEI connector of the radio connection cable to the PEI socket of the radio. For reference, see the following images: 7.1 MOTOROLA MTM800 FuG ET ler! elle Power supply LARDIS LAR-1192 Page 8 of 22 RTM:IT 2022-11-30...
- Page 9 Console Interface configured in the radio is used to transmit the ETSI PEI commands. The PEI connector of the LARDIS ONE connection cable must be plugged into this If two accessory devices are connected to a shared CI on the S/E block via a CIB, only one device may use the head interface and the other the data interface.
- Page 10 Programming/data cable via jack socket connection on the control handset (HBCx) Programming/data cable directly to HD15 LARDIS ONE connection cable (LAR-1109 or LAR-1115) External SIM card reader In summary, only one component from the left column and one component from the right column may be connected to a CIB at the same time.
- Page 11 (LAR- 1116 or LAR-1117), and this is then connected to the rear accessory connection socket of the radio. Accessory socket ler! elle LAR-1116 or -1117 Audio connectors Power supply LARDIS LAR-1192 Page 11 of 22 RTM:IT 2022-11-30...
- Page 12 Push-To-Talk A yellow Push-To-Talk B grey Hands-free microphone + pink Hands-free microphone - blue 12V output radio Ignition input radio Speaker Pin 1 Hands-free microphone 12V output Pin 8 Ignition input LARDIS LAR-1192 Page 12 of 22 RTM:IT 2022-11-30...
- Page 13 Laying the single strands: LARDIS LAR-1192 Page 13 of 22 RTM:IT 2022-11-30...
- Page 14 The parallel black stranded wire is an additional ground reference point to the trigger line, which does not necessarily have to be connected, since this is potential-equal with the terminal 31 supply connection in the line set. FBAS input (RCA) ler! elle Trigger input LARDIS LAR-1192 Page 14 of 22 RTM:IT 2022-11-30...
- Page 15 The socket is located on the left side, directly next to the outlet of the cable set. The OTG adapter provides a USB-A host socket for connecting USB add-on components. connection to radio message receiver (View from the back side) LARDIS LAR-1192 Page 15 of 22 RTM:IT 2022-11-30...
- Page 16 For serial devices, the level converter LAR-1163, which is available as an additional special accessory, is also required. LAR- 1163 Serial connection to radio message receiver (View from the back side) LARDIS LAR-1192 Page 16 of 22 RTM:IT 2022-11-30...
-
Page 17: Connection Of External Control Elements
The corresponding USB plug is connected as previously described in chapter 9. LAR- 1163 Button LAR- connections 1164 Various functionalities can be assigned to the inputs SW_IN1 to SW_IN3 using the program LARDIS ONE Setup. LARDIS LAR-1192 Page 17 of 22 RTM:IT 2022-11-30... - Page 18 The screw set Fehler! Verweisquelle konnte nicht gefunden werden. also includes two screws to secure the lid. The corresponding screw threads are marked with red arrows in the illustration. microSD LARDIS LAR-1192 Page 18 of 22 RTM:IT 2022-11-30...
-
Page 19: Configuration And Update
For configuration and software update, open the cover on the lower side of the device and connect the enclosed USB-C connection cable to the device and a suitable PC or notebook (Microsoft Windows 10 or higher). The corresponding software LARDIS ONE Setup 2.x as well as the documentation are available at https://lardis-one.de/updates/... -
Page 20: Technical Data
TDD (4G) - B40, B38/B41 A-GPS, GLONASS, BEIDOU, Galileo WLAN Internal camera 16MP Autofocus External camera analog input for FBAS PAL via RCA Serial communication (PEI) RS232 Sensors Light sensor Ambient light Motion sensor Accelerometer, compass LARDIS LAR-1192 Page 20 of 22 RTM:IT 2022-11-30... - Page 21 Usage environment Permitted operating temperature -10°C - +60°C Permitted storage temperature -20°C - +70°C Permitted humidity 90% maximum, non-condensing Subject to technical changes and errors LARDIS LAR-1192 Page 21 of 22 RTM:IT 2022-11-30...
- Page 22 RTM Informationstechnologie GmbH & Co. KG Würzburger Straße 197 90766 Fürth Germany info@rtm-it.de www.rtm-it.de LARDIS LAR-1192 Page 22 of 22 RTM:IT 2022-11-30...