Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
EN
Important: Read and
follow all instructions
and SAFETY
PRECAUTIONS before
using this equipment.
Retain for future
reference.
Tank Model
183S2-1500
183S2-1510
183S2-1513
183S2-1514
183S2-1520
183S2-1523
183S2-1524
183S2-1530
183S2-1533
183S2-1534
183S2-1540
183S2-1543
183S2-1544
77-3137-R3 (6/2022)
183S2 (STAINLESS STEEL) 15 GALLON ASME TANKS
2" NPT BOTTOM OUTLET TANKS
STAINLESS STEEL 15-GALLON MODELS
WITH 2 INCH BOTTOM OUTLET
Regulation
None
Single (Regulated air to tank only)
Single (Regulated air to tank only)
Single (Regulated air to tank only)
Double (Regulated air to tank and gun)
Double (Regulated air to tank and gun)
Double (Regulated air to tank and gun)
Extra Sensitive
Extra Sensitive
Extra Sensitive
Extra Sensitive w/ gun regulation
Extra Sensitive w/ gun regulation
Extra Sensitive w/ gun regulation
DESCRIPTION
Binks pressure feed tanks are intended
for use as a pressure container to supply
material at a constant preset pressure up
to a maximum of 110 psi. The tanks are
built to ASME specifications, and also
certified for vacuum operation.
ACTUAL CAPACITIES
15-Gallon holds 19.8 gallons
Agitation
None
None
Gear-reduced (Heavy-duty)
Direct Drive (Heavy-duty)
None
Gear-reduced (Heavy-duty)
Direct Drive (Heavy-duty)
None
Gear-reduced (Heavy-duty)
Direct Drive (Heavy-duty)
None
Gear-reduced (Heavy-duty)
Direct Drive (Heavy-duty)
1 / 12
www.carlisleft.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Carlisle BINKS 183S2-1514
Summary of Contents for Carlisle BINKS 183S2-1514
- Page 1 SERVICE MANUAL 183S2 (STAINLESS STEEL) 15 GALLON ASME TANKS 2" NPT BOTTOM OUTLET TANKS DESCRIPTION Important: Read and Binks pressure feed tanks are intended follow all instructions for use as a pressure container to supply and SAFETY material at a constant preset pressure up to a maximum of 110 psi.
- Page 2 In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: WARNING NOTE CAUTION Hazards or unsafe practices which Hazards or unsafe practices which could result in severe personal Important installation, operation or could result in minor personal injury, injury, death or substantial property maintenance information.
-
Page 3: Pressure Relief Procedure
15-GALLON STAINLESS STEEL TANK ASSEMBLIES – SAFEGUARDS The following hazards may occur during the normal use of this equipment. Please read the following chart. HAZARD CAUSE SAFEGUARDS Fire Solvents and coatings can be highly 1. Adequate exhaust must be provided to keep the air free flammable or combustible, especially of accumulations of flammable vapors. -
Page 4: Specifications
15-GALLON STAINLESS STEEL TANK ASSEMBLIES – SPECIFICATIONS & OPTIONS SPECIFICATIONS STAINLESS STEEL TANKS Maximum Working Pressure 110 psi Tank Shell 304 Stainless Steel Tank Lid 304 Stainless Steel 2" NPT Fluid Outlet Bottom 304 Stainless Steel Agitator Paddle/Propeller Nylon, Glass Filled Agitator Shaft 303 Stainless Steel Agitator Shaft Seal... -
Page 5: Maintenance
15-GALLON STAINLESS STEEL TANK ASSEMBLIES – OPERATION & SERVICE CHECKS OPERATION 4. Loosen thumb screws (17), tip clamps WARNING (16) back and tip lid (11) to one side 1. Close the air inlet valve to tank. Turn High pressure can cause serious injury. of tank. - Page 6 15-GALLON STAINLESS STEEL TANK ASSEMBLIES NOTE NOTE Open side of shaft seal (8) Use PTFE based thread sealant on faces downward. all air and fluid connections. Retainer (9) required only for vacuum operation. CAUTION Use 40 PSI Safety Valve (12) with an extra sensitive regulator.
- Page 7 15-GALLON STAINLESS STEEL TANK ASSEMBLIES – PARTS LIST ITEM 15-GAL PART NO. DESCRIPTION QTY. QMS-46 RETAINING NUT ▲ QMG-85 THRUST WASHER ▲ ----- THRUST COLLAR ▲ ----- SET SCREW (5/16-18 X 3/8) ▲• QMS-447 THRUST COLLAR KIT (INCL 4 & 5) QMS-407 BEARING ASSY ▲...
- Page 8 15-GALLON STAINLESS STEEL TANK ASSEMBLIES – AIR CONTROL SINGLE REGULATOR AIR CONTROL Control tank pressure only. 85-470 for non-agitated tanks 85-471 for agitated tanks *Items with an asterisk are for use with an agitator. ITEM PART DESCRIPTION 85-470 85-471 HAR-511 AIR REGULATOR •...
- Page 9 15-GALLON STAINLESS STEEL TANK ASSEMBLIES – EXTRA SENSITIVE AIR CONTROL EXTRA SENSITIVE REGULATOR AIR CONTROL SINGLE REGULATOR Provides extremely high precision control of tank pressure (only) from 0 – 30 PSI. Includes 40 PSI Safety Valve (not shown.) 85-490 for non-agitated tanks 85-491 for agitated tanks *Items with an asterisk are for use with an agitator.
- Page 10 85-469 CONVERSION TO DOUBLE REGULATOR ASSEMBLY KIT Convert standard single regulator or extra-sensitive air control to a double regulator air control. ITEM PART DESCRIPTION QTY. • — 1/4 NPT PLUG (SUPPLIED W/ REGULATOR) 83-4233 D.M. NIPPLE 1/4 x 3/8 + HAR-507 AIR REGULATOR 83-1355 GAUGE –...
- Page 11 ACCESSORIES VS-534 DISPOSABLE TANK LINERS FLUID STRAINER Molded polyethylene tank liners reduce solvent waste Primary fluid strainer that attaches between and tank cleanup time. The liner is made of tough, fluid outlet valve and fluid hose to strain durable, leakproof poly-ethylene and can be used material.
-
Page 12: Warranty Policy
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Carlisle Fluid Technologies, will void all warranties. Failure to reasonably follow any maintenance guidance provided may invalidate any warranty.
Need help?
Do you have a question about the BINKS 183S2-1514 and is the answer not in the manual?
Questions and answers