Ibera IB-ST20 User Manual

b
c
Max. Load 18 kg / 39.5 lb. (
Warning
Do not mount hanger on drywalls (plasterboard), or wooden panel walls unless there is a wooden stud behind it. Use drill bit of
appropriate size and type: e.g. masonry drill bit for masonry. Avoid any electrical, plumbing, or water fittings hidden in or behind walls.
If you lack the DIY skills to install hanger, seek professional help.
1
警告(繁體中文) 、請勿將本產品鎖固在沒有支撐的牆壁、石膏板或裝飾板上。
4
瓦斯、天然氣或自來水的管線。 、吊掛自行車前，請確認本產品有確實地安裝在實心柱子、樑或牆上，以避免對人和自行車造成損傷。
能安裝，請尋求專業幫助。
Instructions
fig. 1
Hanger folded
1
2
fig. 3b
Mount Front Wheel Bracket
Mount hanger on a solid wall, or along wall stud (upright timber) of a
plasterboard wall (drywall). Mount in a place with adequate space
where it is unlikely to cause obstruction, be knocked or bumped, or
interfered with by young children. Determine correct height for hanger
(rear tyre should sit between 5 cm (2") and 10 cm (4") off floor or ground),
and make sure it is in a straight vertical position (fig. 4).
Erect hanger by fitting brace into brace recess (fig. 2). Determine Mounting Height: put hanger on floor, brackets facing down. Place
bike's front wheel in hanger. Move hanger and bike so rear wheel is nearly touching wall (fig. 3). Hold bike, place your foot on lower
bracket to keep it in place, lift front of bike and shift it slightly rearward until front tyre makes contact with the 2 touch points on wheel
holder. (fig. 3b), and rear wheel is touching the wall. Mark centre hole in upper bracket with a pencil (fig. 5b). Then measure distance
from wall to mark on floor (A). To this measurement add 5 to 10 cm (B). Mark Mounting Height (C = A+B): the position of hanger's
upper bracket centre drill hole on wall (measured from floor) (fig. 4). Fold hanger before mounting on wall.
a
Parts
a Upper bracket
b Wheel holder
c Brace
d Brace recess
d
e Lower bracket
f Rear wheel rest
e
g Wall plugs (screw anchors) x 5
(for masonry or concrete walls only)
18 kg)
最大載重
h Screws x 5
Mount Hanger Mount Hanger
Determine Mounting Height
A = Distance from rear of bike to
upper bracket centre hole
B = Distance between floor
and rear tyre
fig. 2
C = A+B: Mounting height
Hanger erected
Mark Mounting Height
Hold tyre against 2 wheel
holder touch points
Roll-On Bicycle Wall Hanger Roll-On Bicycle Wall Hanger
Storage or display rack.
Compatibility
g
f h
Wheel size: 20–29".
Tyre Width: 2.3–6.3 cm (0.9–2.5").
Not suitable for bikes with mudguards (fenders).
Tools Required
Tape measure
Stud finder (for drywalls or wooden panel walls)
Spirit level (optional)
Drill
Drill bit
Phillips head screwdriver
Hammer (if wall plugs are used)
2 6.5mm
、磚塊或水泥牆請使用
Floor
fig. 3a
Wall
fig. 4
Width: 2.3–6.3 cm (0.9–2.5").
Tyre
3
的鑽頭鑽孔。 、安裝時請避開電子電路，
5
、如果您缺乏
B
A
C
Rear wheel
rest
Min. height 5 cm (2") – 10 cm (4")
Floor
DIY
技
Wall