Eachine EV100 - NEW 5.8G FPV Goggles Manual

Product Contents

Controls Diagram

Controls

Mode/Brightness/Contrast control

Mode:

1. Debug mode: Press "mode" button and power on, enter debug mode (5300MHz).
2. Racing mode: Long press "mode" button until first beep to switch mode from 4 pilots/6 pilots/8 pilots. For example:
   4 pilots/6 pilots/8 pilots/exit racing mode switching circularly.
3. Auto search: Long press "mode" button until second beep to enter auto search.
4. Turn on/off RX: Long press "mode" button until third beep to enter AV IN (RX OFF).

Brightness: Pressing forward/back increases/decreases display brightness.(32 level contrast for the LCD display, default level 28)

Contrast: Pressing left/right decreases/increases display contrast.(32 level contrast for the LCD display, default level 28)

Channel/Band select

Channel: short Press channel up/down buttons will cause the channel to incrementallyincrease/decrease from channels 1 to 8 (refer to frequency table).

Band: Press channel up/down buttons 3s will cause the band to incrementallyincrease/decrease from band A to H (refer to frequency table).

Turn on/off OSD: Press channel up/down buttons simultaneously to turn on/off OSD.

Low battery warning: Buzzer warning if input voltage drops below 6.8V.

Turn on/off fan

Focal Length Adjustment

Adjustable focal length is perfect for myope under 400 degree and hyperope under 100 degree.

Thumbwheel is used to adjust focal length. (+) means to increase diopter, (-) means to decrease diopter.

IPD Adjustment

Independent control for both sides, adjust the range of 58 ~ 68mm.

Slider is switch to adjust IPD. (+) means to increase IPD,(-)means to decrease IPD.

AV In/Out

3.5mm AV Connector

AV input & output

Support external HDMI to AV input

Support external DVR.

USB In

• For firmware upgrading.
• Alternative power supply.

If multiple power sources are supplied at same time (Like: power Bank and head strap battery)the goggles will draw power from the highest voltage.

Mode

In this mode, the best results can be achieved by using the supporting vtx.

Racing Mode

3 Racing Mode: 4/6/8 pilots

60-80MHz interval between adjacent channels greatly decrease interference.

Debug Mode

Press "mode" button first and then powering on goggles, enter debug mode (5300MHz). Requires a corresponding vtx which support pitmode and extra frequency 5300MHz.

Battery

Li-Po BATTERY PACK
7.4V 1000mAh(7.4Wh) with LED indicator
(One charging indicator light, one power-checking button and four power indicator lights)

It can simultaneously power the external DVR.
Made in china

Battery charging

Charge max rate of 1C(DC connector)

USB charging with approved adapter
( USB:5V==1.5A or 2A)

It is not recommended to charge the battery via PC USB, since the insufficient current will damagethe battery.

Do not open the battery case Never leave batteries near fire or high temperatures
Battery may balloon or catch fire if faulty or improperly charged
Never leave a charging battery unattended
Do not use if signs of failure

Detachable Patch

Snap joint assemblies allows easy replacement and maintenance

Replaceable sponge

Using Velcro as a bridge, sponge and flannel can be easily replaced, and Velcro can be used for a long time.

Product specifications

Band & Frequency table

Unit: MHZ

Racing mode frequency

OSD display

Regular mode: Display values like: Band-r CH1 5658MHz
(refer to frequency table)

Racing mode:

Trouble Shooting

No image, display is completely dark

• No power supplied. Check power connections.

No image, display is glowing dark grey

• If using wireless module, ensure RX is working.
• If using AV in cable, check video source.
• Ensure TX is on and camera connections solid
• Ensure lens cap is removed from camera

Complete white screen

• LCD driver has failed and needs to be replaced under warranty. Contact your retailer.

Short range

• Ensure 5.8Ghz antenna were installed.

WWW.EACHINE.COM