Table of Contents
Advertisement
Quick Links
R2E280-AE52-05
CONTENTS
Item no. 10947-5-9970 · ENU · Change 202174 · Approved 2019-01-03 · Page 1 / 10
Operating instructions
1. SAFETY REGULATIONS AND INFORMATION
Read these operating instructions carefully before starting work on the
device. Observe the following warnings to prevent malfunctions or
danger to persons.
These operating instructions are to be regarded as part of the device.
The device is only to be sold or passed on together with the operating
instructions.
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1
1.1 Hazard levels for warnings
1
1
These operating instructions use the following hazard levels to indicate
1
potentially hazardous situations and important safety regulations:
1
2
2
2
2
2
2
3
4
4
5
5
5
5
6
6
1.2 Staff qualifications
6
The device may only be transported, unpacked, installed, operated,
6
maintained and otherwise used by suitably qualified, trained and
7
authorized technical staff.
8
Only authorized specialists are permitted to install the device, to carry
8
out a test run and to perform work on the electrical installation.
8
1.3 Basic safety rules
8
The safety hazards associated with the device must be assessed again
9
following installation in the final product.
9
The locally applicable industrial safety regulations are always to be
9
observed when working on the device.
Keep the workplace clean and tidy. Untidiness in the work area
increases the risk of accidents.
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.
1.4 Voltage
; Check the device's electrical equipment at regular intervals; see
Chapter 5.2 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Indicates an imminently hazardous situation which will result in
death or serious injury if the specified actions are not taken.
Compliance with the instructions is imperative.
WARNING
Indicates a potentially hazardous situation which can result in
death or serious injury if the specified actions are not taken.
Exercise extreme caution while working.
CAUTION
Indicates a potentially hazardous situation which can result in
minor or moderate injury or damage to property if the specified
actions are not taken.
NOTE
A potentially harmful situation can occur and, if not avoided, can
lead to property damage.
DANGER
Electrically charged device
Risk of electric shock
→ When working on an electrically charged device, stand on a
rubber mat.
Advertisement
Table of Contents
Related Manuals for ebm-papst R2E280-AE52-05-FAN
Summary of Contents for ebm-papst R2E280-AE52-05-FAN
-
Page 1: Table Of Contents
Note the following when working on the device: ; Do not perform any modifications, additions or conversions on the device without the approval of ebm-papst. 1.4 Voltage ; Check the device's electrical equipment at regular intervals; see Chapter 5.2 Safety inspection. -
Page 2: Safety And Protective Features
Operating instructions R2E280-AE52-05 CAUTION → Do not wear any loose-fitting or dangling clothing or jewelry Electric charge on capacitor after device is switched off while working on rotating parts. Electric shock, risk of injury → Protect long hair with a cap. →... -
Page 3: Intended Use
Operating instructions R2E280-AE52-05 2. INTENDED USE The device is exclusively designed as a built-in device for conveying air according to its technical data. Any other usage above and beyond this does not conform with the intended purpose and constitutes misuse of the device. Customer equipment must be capable of withstanding the mechanical and thermal stresses that can arise from this product. -
Page 4: Technical Data
Operating instructions R2E280-AE52-05 3. TECHNICAL DATA 3.1 Product drawing All dimensions in mm. Cable silicone 4G 0.5 mm², 4x crimped splices Accessory part: inlet ring 96360-2-4013 not included in scope of delivery Max. clearance for screw 6 mm Item no. 10947-5-9970 · ENU · Change 202174 · Approved 2019-01-03 · Page 4 / 10... -
Page 5: Nominal Data
With regard to cyclic speed loads, note that the rotating parts of the device are designed for a maximum of one million load Motor M2E068-EC cycles. If you have special questions, consult ebm-papst for support. Phase ; Use the device in accordance with its degree of protection. -
Page 6: Connection And Startup
Bearing damage, shorter service life ; If the motor run capacitor was not installed by ebm-papst, check → The fan must not be subjected to force or excessive vibration whether the information on the motor run capacitor matches the from sections of the installation. -
Page 7: Connection Diagram
Operating instructions R2E280-AE52-05 4.4 Connection diagram blue brown black green/yellow Item no. 10947-5-9970 · ENU · Change 202174 · Approved 2019-01-03 · Page 7 / 10... -
Page 8: Checking Connections
Operating instructions R2E280-AE52-05 4.5 Checking connections 5. MAINTENANCE, MALFUNCTIONS, POSSIBLE CAUSES AND REMEDIES ; Ensure isolation from supply (all phases). ; Make sure a restart is impossible Do not perform any repairs on your device. Send the device to ebm- ;... -
Page 9: Cleaning
At least every Replace device Only ferrite magnets and not rare earth magnets are used in external bearing noise 6 months rotor motors from ebm-papst Mulfingen GmbH & Co. KG. Vibration test Vibration tester, Recommended Clean impeller ; Ferrite magnets can be disposed of in the same way as normal iron... - Page 10 Operating instructions R2E280-AE52-05 Dispose of electronic components employing the proper procedures for electronic scrap. → Please contact ebm-papst for any other questions on disposal. Item no. 10947-5-9970 · ENU · Change 202174 · Approved 2019-01-03 · Page 10 / 10...
Need help?
Do you have a question about the R2E280-AE52-05-FAN and is the answer not in the manual?
Questions and answers