Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for SIXTY82 M29S LENGTH 300
- Page 1 The new original ORIGINAL USER MANUAL – PART 1 GENERAL REQUIREMENTS...
- Page 2 NB! PART 1 is inseparable connected with the applicable user manual PART 2 March 2019 Manufacturer: SIXTY82 B.V. Amperelaan 9 9207AM Drachten The Netherlands Phone +31 (0)88 1342200 Email info@sixty82.nl...
-
Page 3: Table Of Contents
Content 1. INTRODUCTION 11. INSPECTIONS 11.1 GENERAL 11.2 INSPECTION LEVELS 2. SCOPE 11.3 INSPECTION FREQUENCY 3. IDENTIFICATION 12. MAINTENANCE AND DISCARD CRITERIA 12.1 DISCARD AND REJECTION CRITERIA 4. LIMITATIONS OF USE 12.2 GENERAL 12.3 MAIN CHORDS 5. SAFETY INSTRUCTIONS 12.4 BRACES 5.1 ELETRICAL POTENTIAL BONDING 12.5 CONNECTORS 12.6 PINS... -
Page 4: Introduction
This signal word is to be limited to the most extreme situations. 3. IDENTIFICATION SIXTY82 products can be recognised by the specific ID-tag on all trusses as well as the embossed logo on each coupler. WARNING: Indicates a hazardous situation which, if not avoided, could result in death or To identify individual parts, see figure 3.1... -
Page 5: Limitations Of Use
If temperatures are bellow 0°C, captive water caused by intrusion or condensation will freeze and can cause damage to the truss members. To avoid this effect SIXTY82 can provide the same trusses with 100% circumferential welded diagonals as well as drainage holes. -
Page 6: Eletrical Potential Bonding
For an overview of approved accessories, we refer to our sembling, disassembling or transporting truss brochure or our website: www.sixty82.com. elements. Assembled trusses and structures must be checked on their It is of great importance that accessories never damage the truss. - Page 7 The use of slinging devices with a soft cover is advised. Direct contact between a steel wire rope and the truss chord should be avoided because of the abrasive surface of the steel wire rope. For stability reasons it is advised to wrap at least 2 main chords.
-
Page 8: Assembly Instructions
10.1 ASSEMBLY 10. ASSEMBLY & DISASSEMBLY Slide two trusses towards each other. INSTRUCTIONS Look if the pin holes are more or less alligned. NB! With conical truss there is always a small difference in allignment. This is done on purpose in order to maintain the Trusses and truss constructions shall be assembled by some functionality of the conical connection system. -
Page 9: Inspections
SIXTY82 trusses need to be checked and inspected configuration where movement of the truss system is an integral part of use. -
Page 10: Maintenance And Discard Criteria
Fig. 9.1 Table 1 Inspection level Items to be inspected Part Initial Regular Periodic Chords Diagonals Connectors Welds Fasteners Geometry ID-TAG Chapter 11.2 Chapter 11.2 Chapter 11.2 Missing parts Dents Bends Holes (1) Incorrect repair Abrasion Corrosion Missing members Flatness (2) Deformation Excessive wear Cracks... -
Page 11: Main Chords
used or stainless- s t e e l versions in order to prevent possible dangers by galvanic corrosion. Damaged or worn material shall be clearly marked and immediate taken out of service. 12.6 PINS Pins undergo wear when inserted and removed frequently, in particular by hammer strokes. -
Page 12: Guarantee
For a period of 12 month we undertake to repair, free of charge any damage attributable to faulty materials or workmanship, provided that the appliance is forwarded, freight paid, to our works or one of the SIXTY82 contract service organisations. Extended warranty can be obtained by registering your products at www.sixty82.com...
Need help?
Do you have a question about the M29S LENGTH 300 and is the answer not in the manual?
Questions and answers