IS ALLOWED ONLY FOR INDIVIDUALS WHO HAVE BEEN AUTHORIZED TO CARRY OUT SUCH WORKS, HAVE RECEIVED TRAINING ON THE OPERATION OF THE GAUSS MIL, HAVE READ THE OPERATING MANUAL FOR THE DEVICE, AND HAVE BEEN GRANTED PERMISSION UNDER RELEVANT ORDERS TO PERFORM SUCH ACTIONS.
+ connector protection cap 11. Tiger search coil + coil cover + connector protection cap 12. MarsMD Pointer 13. Carry bag The Gauss MiL can be additionally equipped with the different sized search coils: GOLIATH DISCOVERY TIGER SNIPER search coil...
ASSEMBLY Assembling the Gauss MiL proceeds via the following steps: 1 Attach the control box to the end of the shaft handle. 2 Adjust the shaft length to fit your height and tighten the twist lock to secure. nsert the rubber washers into the holes of the lower shaft yoke and place the yoke between the mounting tabs on top of the coil.
TURNING THE DETECTOR ON To turn on the device, press . You will hear a melody and "On" message will be shown on the display. Once turned on, the detector is ready for operation and automatically enters the search mode. Quick press to turn off...
CONTROLS Wireless Audio Appears when the built-in transmitter is activated. A digit nearby stands for the number of the current radio channel for sound transmission. Backlight Indicator Operating Frequency Appears when the screen backlight is on. Indicates the current operating frequency. Battery Status Indicator TARGET ID...
SETTINGS MENU The Gauss MiL Settings Menu contains 5 adjustable settings. Press for the first time and the current setting and its Target ID value will be displayed on the screen. Pressing repeatedly calls up other possible menu settings. If you want to...
Page 8
OPERATION MODE MODE mode for the use in both humanitarian and military demining. is a special mode designed to detect metal-containing explosives. In this mode, the metal detector has one tone audio indication without determining the type of metal (ferrous/non-ferrous), TARGET ID isn’t displayed on screen. The audio tone increases/decreases as the coil approaches/gets farther away from a target.
GROUND BALANCE The ground balance setting It’s very important to always set the can be adjusted in two ways: ground balance before starting the manually (Hd) and automatically (At). search. If the detector isn’t properly ground balanced, its searching abilities may be reduced You can switch between these two options by that way causing unstable operation and pressing...
Page 10
The ground balance value provides the current information about the ground you are searching on. The range of 6-20 is common to poorly mineralized sandy soils. The range of 20-45 is typical for dry clay loams and black soils with low salt content. The same soils at high humidity and low temperature may have the values within the 45-60 range.
PINPOINT In the An mode, the Gauss MiL operates as a To determine the exact position motion detector, that’s why you should of a target: constantly move the coil over the ground in After the approximate target location order for the device to detect targets. While is detected, move the coil away from moving, it’s not always possible to effectively...
BACKLIGHT The Gauss MiL LCD is equipped with a built-in backlight for operation in dark conditions. It has 4 brightness levels. The last selected level will be saved in the detector’s memory after it’s turned off. Press and hold to turn the backlight on or off. When...
To charge the Gauss MiL, the use of any quick charge AC power adapters is prohibited! It may cause damage or destroy the battery. Use the power adapter supplied in the package.
CONNECTING HEADPHONES How to connect your headphones to the MDLink module: 6.35 mm (1/4’’) Charging 1 Plug your headphones into a 6.35 mm Headphone Socket headphone jack on the MDLink module. Socket 2 Turn on the detector and the module Power Battery Button...
FACTORY SETTINGS All settings are saved in the Gauss MiL`s memory after it’s turned off and are automatically restored after it’s turned on. TO RETURN YOUR SETTINGS TO THEIR FACTORY PRESETS, PERFORM THE FOLLOWING STEPS: Turn off the detector. Press and hold...
MAINTANENCE & SAFETY The Gauss MiL is a high-quality electronic device, therefore proper care and maintenance is essential to ensure its continuous reliable operation. GAUSS MIL CARE: • Do not leave the detector in extreme cold or heat (e.g. in a hot car) as well as in damp locations.
TECHNICAL SPECIFICATIONS Gauss MiL Detector Detecting Range Max range ≈ 150 сm Operating Frequency 15.8...16.2 kHz Visual Indication Audible 4-tone volume control Metal detector (An) with metal discrimination Search Mode Mine detector (iL) without metal discrimination Manual ground balance performed manually...