Advertisement
Welcome to B-hyve™
Water intrusion in the home causes extensive damage unless it is caught right away. The B-hyve™ Flood Sensor offers peace of mind and protection by alerting your phone immediately when a leak in your home is detected.
Device Оverview
Front
Back
Inside
B-hyve Gen 2 Hub
Open the B-hyve™ App
Log into your B-hyve account and tap "My B-hyve". Go to "devices" then "add device". The app will walk you through the rest of the process.
For new users, search apps for "B-hyve" and download the free Android or iOS app.
Create an account to begin setup.
Power and Pair Gen 2 Hub
Plug the hub into an indoor outlet, central to sensor locations, and within range of Wi-Fi. Press 
button five times to reset the hub and enter into pairing mode. Your hub will flash red, then blue to signify it is in pairing mode.
Power and Pair Sensor
Remove the pull tab to activate the battery, your sensor is now in pairing mode.
If at any time you need to re-pair, quickly press the on the back of the sensor 5 times.
Sensors include one Lithium CR2032 battery. Annual battery replacement is recommended for optimal performance. See the "Replacing the Battery" section for instructions.
Select Sensor Location
Place the sensor in an indoor location within range of your hub. Range is approximately 150 ft. (45m), walls and other interference can reduce this range. Position the retrieval cord for easy extraction when placing a sensor beneath heavy objects.
If using as a water sensor:
- Place the sensor flat on the floor in the area you wish to monitor.
- Ensure that the flood sensor is positioned with its flat surface faced down.
If using as a heat/cold sensor:
- Place in the location where you wish to detect changes in temperatures.
- Avoid areas where inconsistent temperatures are common. (near vents, exhausts, etc.)
The sensor communicates with the hub via Bluetooth™; the range between the sensor and hub will vary depending on the number of walls and types of obstacles the signal needs to travel through.
If water is detected or there is a temperature fluctuation, a beep will play and a notification will be displayed on your phone.
Avoid areas where the signal must travel through dirt or thick steel barriers.
Complete Setup
Continue to follow the instruction within the app to complete the setup process.
Replacing the Battery
- Insert a flathead screwdriver into the open slot.
- Turn the screwdriver 90º to snap open the cover.
- To remove the battery, lift on the edge of the coin cell battery using your fingers. DO NOT use a screwdriver or other metal object.
- Insert a new CR2032 battery at an angle.
- Verify that the + side is up.
- Reinstall the battery cover by snapping it into place.
Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Even used cells may cause injury.
Dispose of used batteries according to the battery manufacturer's instructions.
Risk of Fire, Explosion, and Electric Shock. Replace battery with CR2032 only. Use of a different battery has the potential for a risk of fire, explosion, and electric shock.
Do not ingest batteries. Chemical Burn Hazard. Keep batteries away from children.
This product contains a lithium button/coin cell battery.
If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours.
Specifications
Sensor
HVIN: FS1
Part No – 71003, 71000, 04133
FCC ID:ML6FS1
IC:3330A-FS1
RATING: DC 3.3V
Battery: CR 2032 Lithium (Non-Rechargeable)
Temp Range: 32-158°F (0-70°C)
Hub
HVIN: BH1G2
Part No – 21008
FCC ID:ML6-BH1G2
IC:3330A-BH1G2
Range: 150 ft. (45m) without interference
Temperature Operating Range: 32°F-104°F (0-40°C)
Storage Temperature: -4°F to 140°F (-20°C to 60°C)
Humidity Operating Range: 0–90%
Input: 100-240V ~ 50/60Hz 0.2A
Output: 5V-1.0A
Need Help?
If you encounter a problem, please use the following resources before returning your B-hyve to the store.
Scan the QR Code for access to the Orbit online help center.
call us: 1-800-488-6156
Text us: 801-797-2319
or visit us at:
community.orbitonline.com
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the 71000 and is the answer not in the manual?
Questions and answers