B-hyve 21004 - Smart Hose Watering Timer Manual

Table of Contents

Contents

1 Box Contents
2 Open the B-hyve App
3 Power Your Wi-Fi Hub
4 Enter Pairing Mode
5 Power Your Hose Faucet Timer
6 Install the Timer
7 Turn on Your Water
8 Manual Watering
9 Timer
10 Hub
11 FCC Statement
12 Need Help?
13 Documents / Resources
- 13.1 References
- 13.2 Download manual

Box Contents

Hose Faucet Timer
Wi-Fi Hub
Quick Start Guide

Open the B-hyve App

Log into your B-hyve account and go to devices under settings to add the Hose Faucet Timer as a new device. The app will walk you through the rest of the process.

information For new users, search for "B-hyve" and download the free Android or iOS app. Create an account to begin timer setup.

Power Your Wi-Fi Hub

Write down the MAC address:
12-digit alphanumeric code on the back of the hub.

Hub MAC Addresss:

Plug the hub into an indoor outlet within range of your B-hyve device and Wi-Fi signal.

information Avoid areas where the signal must travel through dirt or thick steel barriers.

Enter Pairing Mode

Press the B-hyve button to enter into pairing mode. Your hub will flash a blue light every 5 seconds.

Power Your Hose Faucet Timer

Insert two new AA Batteries*, the timer is now in pairing mode and will flash a blue light every 5 seconds.

You will also hear two clicks about 6 seconds apart, this is normal and ensures the valve is closed before you turn on the water.

Write down the MAC address: 12 digit alphanumeric code on the bottom of the timer.

Timer MAC Address:

information If at any time you need to re-pair or do a factory reset, press the on/off button quickly 5 times.

*Batteries are sold separately. Replace batteries when timer flashes a red light every 5 seconds, or when the app notifies you that batteries need replacing.

warning If you remove or change the batteries you will need to reconnect to Bluetooth® to set the correct time and date.

Install the Timer

Your timer is now ready to be used with any product that can be attached to a standard hose faucet.
Install the Timer

information Do not place the timer in an underground valve box.

Turn on Your Water

The water must remain on for the timer to work properly.

Manual Watering

Simply press and hold the on/off button for 5 seconds to activate manual watering.

Need to stop watering, even during a programmed time? Press the on/off button once to stop watering.

Timer

Range: 150 ft without interference
Pressure Operating Range: 10-100 PSI
Temperature Operating Range:
32°F-158°F (0-70°C)
For Outdoor Use With Cold Water Only
Not For Use With Appliances
Do Not Mix Alkaline, Standard (Carbon-Zinc), or Rechargeable (Nickel Cadmium) Batteries.
Used up or dead batteries must be removed from the timer and disposed of properly.
Do not dispose of batteries in fire.
Batteries may explode or leak.

Hub

Range: 150 ft without interference
Temperature Operating Range: 32°F-104°F (0-40°C)
Storage Temperature: -4°F to 140°F (-20°C to 60°C)
Humidity Operating Range: 0–90%
Input: 100-240V ~ 50/60Hz 0.2A
Output: 5V-1.0A
For Indoor Use Only

FCC Statement

FCC ID: ML6HT25 & ML6-BH1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

FCC Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from the receiver's.
Consult the dealer or an experienced radio/TV technician for help.

IC Statement: IC: 3330A-HT25 & 3330A-BH1
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.

Need Help?

If you encounter a problem, please use the following resources before retuning your B-hyve to the store.

Scan the QR Code for access to a full user manual, videos, and more.