Summary of Contents for Lincoln Electric DAMPER BOX DUALFLOW
Page 1
CONTROL UNIT DAMPER BOX DUALFLOW SAFETY INSTRUCTIONS FOR USE AND MAINTENANCE No W000375442 8695 8600 EDITION : EN Instructions for use REF : REVISION : B DATE : 05-2021 Original instructions...
Page 2
Thank for the trust you have expressed by purchasing this equipment, which will give you full satisfaction if you follow its instructions for use and maintenance. Its design, component specifications and workmanship comply with applicable European directives. Please refer to the enclosed CE declaration to identify the directives applicable to it.
DELIVERY ..........................6 TECHNICAL SPECIFICATIONS ....................6 D - TECHNICAL DESCRIPTION ....................... 7 DESCRIPTION OF CONTROLS OF THE DAMPER BOX DUALFLOW UNIT ....... 7 OPERATING PRINCIPLE ......................8 DAMPER BOX DUALFLOW COMPOSITION ................. 9 CONNECTING THE OPTIONAL CURRENT CLAMPS AND SENSORS ........ 10 SETTING THE DAMPER CLOSING DELAY ................
Page 4
8695 8600 REVISIONS REVISION B 05/21 DESIGNATION PAGE Created in English DAMPER BOX DUALFLOW...
Page 5
8695 8600 LINCOLN ELECTRIC FRANCE SAS Avenue Franklin Roosevelt 76120 – LE GRAND QUEVILLY DAMPER BOX DUALFLOW UNIT CE DECLARATION OF CONFORMITY CE/EU DECLARATION OF CONFORMITY Dear customer, This CE/EU declaration of conformity certifies that the supplied equipment complies with applicable laws and regulations when used in accordance with the enclosed instructions.
Before the filter is used by a new user, make sure that they have read this manual and understood all the explanations provided. For any further information, please feel free to contact the technical departments of LINCOLN ELECTRIC. MACHINE GUARANTEE This machine is guaranteed for 12 months from the date of purchase.
(speed of air in the piping) and head loss. In accordance with the regulations of CARSAT and INRS, the installation must be inspected from time to time to make sure that it continues to comply with its reference values. DAMPER BOX DUALFLOW...
If the filter is replaced, use another one with the same part number (shade number). Persons in the vicinity of the operator, especially any helpers, must be protected by means of suitable screens, anti-UV goggles or, if needed, masks with suitable protective filters (EN 139). DAMPER BOX DUALFLOW...
Page 10
A work permit procedure setting out all the safety measures must systematically be set up. Make sure that ventilation is appropriate, paying special attention to: — under-oxygenation — over-oxygenation — excess fuel gas DAMPER BOX DUALFLOW...
— Not obstruct the air outlet of the machine. — Not introduce external elements into the filter (paper, cloths, cigarette butts etc.) — Replace the filter medium with new original Lincoln Electric medium, which alone can guarantee the filtration characteristics.
For your safety and optimum performance, please read this manual carefully before using the filter. The DAMPER BOX DUALFLOW box manages two high-vacuum pneumatic dampers. It must be used along with our range of LINC GUN FX DUAL FLOW fume extraction torches It allows the welder to change the extraction power to suit the type of weld being made by just pressing a micro switch located on the torch handle, during the welding process.
8695 8600 / B D - TECHNICAL DESCRIPTION DESCRIPTION OF CONTROLS OF THE DAMPER BOX DUALFLOW UNIT 1 – Padlockable starting up switch 2 – White power indicator 3 – Damper opening indicator 4 – Auto/manual switch 5 – Momentary or maintained mode selection switch 6 –...
In that case, as extraction is continuous, if the rate has been reduced by selecting the maintained mode when the arc is shut down, the rate will be low when the arc is struck once again. DAMPER BOX DUALFLOW...
PRI 230/400V – SEC 24V transformer to wire according to the supply system voltage PLC that carries out the different functions of the DAMPER BOX DUALFLOW, Current sensor supply board 24VAC power supply for damper coils Current sensor connected by 3.5 mm jack Torch connected by 6.3 mm jack...
CONNECTING THE OPTIONAL CURRENT CLAMPS AND SENSORS The current clamp or inductive current sensor are supplied unwired. In order to connect them to the DAMPER BOX DUALFLOW box, you must either : 1) weld the male 3.5 mm jack to the wires of the current sensor,...
The digit flashes Move the flashing to the digit to modify with the right and left arrows Modify the figure with the up and down arrows Approve by pressing OK and then ESC DAMPER BOX DUALFLOW...
As described in the OPERATING PRINCIPLE section, the Automatic Mode is only available if you connect either : - A current clamp part no. W000380662, (not supplied with the DAMPER BOX DUALFLOW box). ->Detection of continuous currents (DC) > 80A The ground cable must pass through the current sensor, and the sensor clamp must be correctly closed as shown in the photograph above.
8695 8600 / B PERSONAL NOTES Lincoln Electric France S.A.S. Avenue Franklin Roosevelt 76120 Le Grand Quevilly 76121 Le Grand Quevilly cedex www.lincolnelectriceurope.com DAMPER BOX DUALFLOW...