Bosch 06018A9000 Original Instructions Manual page 12

OBJ_BUCH-1843-004.book Page 12 Tuesday, April 12, 2016 12:18 PM
12 | English
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The power tool is intended for dry sanding, structuring and
polishing metal pipes with diametres between 8–120 mm.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Drive roller
2 Locking screw
3 Spindle lock
4 Auxiliary handle (insulated gripping surface)
5 Thumbwheel for belt speed preselection
6 On/Off switch
7 Tensioning arm
8 Guide roller
9 Sanding belt*
10 Guide roller
11 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Pipe Sander
Article number
Rated power input
Belt speed at thumbwheel setting
– 1
– 6
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
1 609 92A 2NZ | (12.4.16)
Pipe Sander
Sanding belt length
Sanding belt width
Suitable pipe diameter
Belt speed preselection
Soft start
Constant electronic control
Restarting Protection
Weight according to
EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 89 dB(A); Sound power level
100 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 60745-2-4:
a =3 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product
described under "Technical Data" is in conformity with all
relevant provisions of the directives 2011/65/EU, until
GRB 14 CE
19 April 2016: 2004/108/EC, from 20 April 2016 on:
3 601 HA9 0..
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745+1,
W 1400
EN 60745+2+4, EN 50581.
Technical file (2006/42/EC) at:
m/s 2.7
Robert Bosch Power Tools GmbH, PT/ETM9
m/s 8.5
70538 Stuttgart, GERMANY
mm
mm
mm
kg
(triax vector sum) and uncertainty K
h
2 2
, K=1.5 m/s .
GRB 14 CE
760
40
8–120




3.7
/II
Bosch Power Tools