Advertisement
3. CONTENTS AND SPECIFICATION
3.1
Carton content
3.1.1
Carefully unpack the carton.
3.1.2
Locate the two side clasps (fig. 1.6) which hold the top section
(fig.1.3) in place.
3.1.3
Undo the clasps, remove the top section and take out the items in
the container.
3.1.4
Check and identify each component as listed below. If anything is
missing or damaged please contact your supplier immediately.
Item
Description
1
Handle
2
ON/OFF switch
3
Top section
4
Filter basket
5
Safety float valve
6
Clasp
7
Container, (Stainless Steel)
8
Vacuum hose connection
9
Castors
10
Flexible vacuum hose
4. ASSEMBLY
4.1
Ensure the mains plug is disconnected.
4.2
Undo clasps.
4.3
Lift off the top section assembly.
4.4
Remove contents from inside the container.
4.5
Turn the container upside down and insert the castors ensuring
they are pushed all the way in.
4.6a
For wet vacuum cleaning fit the supplied foamed plastic filter.
4.6b
For dry vacuum cleaning use the supplied dust bag.
4.6c
Alternatively, for dry vacuuming use the optional cartridge filter.
4.7
Replace the top section onto the container.
4.8
Align up the top section with the clasps and snap into place,
by applying pressure at the mid point of the clasps.
4.9
Insert the large end of the hose into the front inlet of the container
and lock in place by turning clockwise a quarter turn.
4.10
Choose the desired nozzle and push it onto the telescopic suction tube.
5. DRY VACUUM CLEANING
WARNING! Ensure you read, understand and apply Section 1 ‘Safety Instructions’.
p
p
Reminder: DO NOT vacuum hazardous substances. Use of an incorrect dust bag will invalidate your warranty.
5.1
Ensure the machine is unplugged from the power supply.
5.2a
Remove the top section and fit the dust bag flange onto the inlet
stub, taking care not to damage the bag.
5.2b
Alternatively, slide the optional cartridge filter down over the filter
basket and push fully home.
5.3
Reposition the head onto the drum body, and clip in place.
5.4
Insert the larger end of the flexible hose into the front inlet on the
container and lock in place. Push the required attachment onto
the free end of the hose.
5.5
Plug in the power supply.
5.6
Switch to the ‘On’ (position ‘I’).
5.7
When you have completed vacuuming, press the switch to ‘Off’ (position ‘O’)
and unplug from power supply.
Regularly check the dust bag and dispose of safely when it is 2/3 full. The bag is manufactured so that only air, not dust, will pass
through the paper and as such the dust bag must not be re-used. If you wish to use the machine for a wet application and the dust bag
is less than 2/3 full, carefully remove the bag, store for future use, and wipe the tank clean.
DO NOT use the dust bag for wet or sharp materials.
7
6. WET VACUUM CLEANING
WARNING! Ensure you read, understand and apply Section 1 ‘Safety Instructions’. Reminder: Remove plug from power supply
p
p
before opening unit. DO NOT vacuum solvents, explosives, inflammable and/or hazardous liquids such as petrol, oil, spirits, paint,
thinners, acids etc.
6.1
Ensure the machine is unplugged from the power supply. Make sure the tank is clean and free from dust and dirt.
6.2
Remove the dust bag and fit a foam filter over the filter basket. Replace the top section onto the container.
6.3
To the same flexible hose as used in dry cleaning fit the desired nozzle.
6.4
Ensure the switch is ‘Off’ (position ‘0’) before plugging into the power supply.
6.5
Press the switch to ‘On’ (position ‘I’).
Note: To vacuum large quantities of liquid, from a sink or tank etc, do not immerse the nozzle completely in the liquid, leave a gap at the top of
the nozzle opening to allow an air inflow. The machine is fitted with a float valve which stops the suction action when the tank has reached its
maximum capacity. The user will notice an increase in motor speed. When this happens, turn off the machine, disconnect from power supply,
remove the head from the container and empty the liquid into a suitable receptacle or drain. To continue vacuuming, refit the head and proceed.
After wet vacuuming, turn the machine off and unplug from power supply. Empty the container and clean and dry the inside and outside before
storage. Remember! After wet vacuuming the foam filter must be removed and a dust bag or optional cartridge filter must be fitted before dry
vacuuming again.
Item
Description
11
Telescopic suction tube
12
Blow connection
13
Combination nozzle
14
Dust bag
15
Foamed plastic filter
16
Crevice nozzle
17
Dust free tool ON/OFF
18
3 pin socket for tool
19
Cartridge filter (optional)
20
Dust free tool adaptor DFS/AK10
WARNING! Not designed for liquid storage. Always empty liquids after use and before storing.
p
p
fig 1
PC200SDAUTO & PC300SDAUTO - 2 - 22/03/05
Advertisement
