Table of Contents
Advertisement
Quick Links
Contents
Important User Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
Safety Precautions � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
Light Fixture Installation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Light Fixture Electrical Connection � � � � � � � � � � � � � � � � � � � � � � � � 8
Adjustment and Aiming � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
Additional Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
Care and Maintenance � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
Storage Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
Novara helpline number +1-315-883-2434
Visit the Novara LED Light Fixture web page at wengercorp.com for more information.
Note: Please read and understand these instructions before installing or operating�
Note: If you need additional information, contact Wenger Corporation using the information below�
©Wenger Corporation 2023
Wenger Corporation, 555 Park Drive, P�O� Box 448, Owatonna, Minnesota 55060-0448
USA: (800) 4WENGER (493-6437) • Worldwide: +1-507-455-4100 • wengercorp�com
Installation Instructions / Owner's Manual
Novara
Troubleshooting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
Introduction � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
Verify Power Distribution � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
Verify DMX Communication � � � � � � � � � � � � � � � � � � � � � � � � � 12
Printed in USA 2023-05
LED Light Fixture
™
Part #188A633-01
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Wenger Novara
Summary of Contents for Wenger Novara
-
Page 1: Table Of Contents
Storage Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9 Novara helpline number +1-315-883-2434 Visit the Novara LED Light Fixture web page at wengercorp.com for more information. Note: Please read and understand these instructions before installing or operating�... -
Page 2: Important User Information
Wenger Corporation� Wenger Corporation does not assume any responsibility for any errors that may appear in these instructions� In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions�... -
Page 3: Light Fixture Installation
Light Fixture Installation If the light must be installed, use the following procedure. STOP For light use and troubleshooting, go to page 8. 1. Lower the ceiling row to the stage floor in the vertical storage position� 2� Disconnect power to the ceiling row� 3. Unplug the first light fixture from the ceiling raceway� 4. Disconnect the light fixture from the tilt switch. - Page 4 Light Fixture Installation (continued) 5� Remove the junction box� a� Remove the strain relief that passes through the rear of the junction box and light mounting bracket� b� Drill/remove the rivets securing the junction box� c� Remove and discard the junction box�...
- Page 5 7� This step requires two people! One person inserts the Novara light fixture through the hole in the panel while one person loosely attaches it to the light mounting bracket using the new hardware� Leave loose for attaching power and data cables�...
- Page 6 Light Fixture Installation (continued) 8. Connect the safety cable to the first light fixture and the ceiling structural tubing. a. The safety cable should capture both the fixture housing and fixture yoke by passing the carabiner through the pigtail in the safety cable� b� The cable should then be wrapped around the structural steel tubing and the carabiner secured back to the safety cable� Loop around light fixture housing Loop around light fixture...
- Page 7 Light Fixture Installation (continued) 10� Connect the DMX and powerCON cables between all the light fixtures in the ceiling row. powerCON Connection Connection powerCON Connection 11. Connect the house DMX to the first light fixture. House 12. Attach a DMX terminator to the last light fixture in the ceiling row� 13� Tighten the hardware attached in Step 7 at each light� Terminator 14� For cable management, use zip ties to secure the cables to a nearby bowstring�...
-
Page 8: Light Fixture Electrical Connection
2. Connect the powerCON and RJ-45 or XLR DMX cables to the corresponding ports on the first light fixture control box� 3. Connect the powerCON and RJ-45 or XLR DMX cable to the next light fixture in the row. NOTICE Ensure the supply voltage meets the Novara LED light fixture requirements before securing connections. The Novara light fixture requires non-dimmed mains power in the range of 100-240VAC 50/60Hz. 4. Power up the light fixture to ensure proper connections. CAUTION Do not connect or disconnect the LED powerCON connector under load. -
Page 9: Adjustment And Aiming
See the following procedures for light use and troubleshooting. STOP For light fixture installation, go to page 3. Adjustment and Aiming The angle of the LED array can be adjusted at each light fixture. To adjust the up and down angle: 1� Loosen the side adjustment knob and tilt the light fixture to the desired angle. 2�... -
Page 10: Troubleshooting
Troubleshooting Introduction This document provides the procedural information required to troubleshoot a Wenger Novara LED Fixture in the field. The procedures will detail the steps required to accurately determine if a fixture requires further testing/ maintenance at a separate location� CAUTION These procedures should be performed by a qualified person to avoid damage to the fixture. Verify Power Distribution Follow these steps to determine if there is an AC power issue with the fixture. - Page 11 Do not proceed to the next step if power is not being distributed properly. 7� Visually inspect the LED array, LED array wire harness, and optical lenses for any signs of damage� The array, wire harness, and optical lenses are located on the bottom of the fixture secured to the heat sink. LED Array Wire Harness Optical Lens Array 8. Turn off AC power to the fixture and reconnect the downstream AC power wiring to the remaining fixtures. 9. Re-energize the AC power and check the downstream fixtures to see if they are at full intensity as well. 10. If the fixture passes these checks, proceed to verify DMX communication. 11. If the fixture is not functioning, contact a Wenger Corporation Lighting Specialist.
-
Page 12: Verify Dmx Communication
4� Connect ONLY the input DMX line and check for DMX control (dimming operation) utilizing a DMXcat or other DMX/RDM control method� 5. Change the DMX address of the fixture using a DMXcat or other DMX/RDM control method. 6. Verify that the DMX address was recorded in the fixture by dimming only the new address. 7. Connect any downstream fixtures and confirm DMX operation of remaining fixtures. 8� Ensure the sites DMX communication wire is terminated/ended with a resistor at the end of the DMX communication line� 9. If the fixture is not responding to DMX communication, contact a Wenger Corporation Lighting Specialist.
Need help?
Do you have a question about the Novara and is the answer not in the manual?
Questions and answers