Subscribe to Our Youtube Channel
Summary of Contents for cam GAB2 Series
- Page 1 Original operating manual Operating manual Telescopic fork-mounted crane jib GAB2-series Flexibility & experience 06/2021 – V01 from serial n° 500...
- Page 2 © 06-2021. CAM attachments is a trademark of TVH Parts Holding NV, Brabantstraat 15, B-8790 Waregem. All rights reserved. No part of this publication may be reproduced or communicated in any form or by any means, electronic or mechanical, including copying, recording or use in an information storage or retrieval system, without prior and explicit permission of TVH Parts Holding NV.
- Page 3 Bulgarian Можете да намерите това ръководство на Вашия език чрез линка, посочен по – долу. Czech Tento návod najdete ve svém jazyce prostřednictvím odkazu níže. Danish Du kan finde denne vejledning på dit sprog via nedenstående link. German Sie finden diese Bedienungsanleitung in Ihrer Sprache unter folgendem Link. Greek Μπορείτε...
- Page 4 Thank you for using our product. For your safety and to ensure a correct operation, we would like to bring to your attention some aspects of this manual: • This booklet supplies useful instructions for the correct operation and maintenance of the product. It is therefore necessary to pay the utmost attention to all of the paragraphs that illustrate the most simple and secure way to operate and use this product.
-
Page 5: Table Of Contents
CONTENTS INTRODUCTION ..................... DESCRIPTION . -
Page 6: Introduction
INTRODUCTION This manual contains all the necessary information on the installation and operation of the telescopic fork-mounted crane jib. Some of the maintenance operations should only be carried out by professional technicians. If you require this information and the maintenance steps, please contact your dealer. Also included in this manual are a number of safety instructions to create a safe working environment. -
Page 7: Description
DESCRIPTION 2.1. Technical data Always check the type plate for the correct information. The load diagram is mentioned under chapter 3. Safety instructions – 3.2. Load diagram. Type Fork-mounted crane jib manual telescopic Model BA52820 Load capacity (kg) 2000 Load centre (mm) Maximum arm length (extended) (L2) (mm) 3000 Maximum fork spread measured over the forks (W11) (mm) -
Page 8: Main Components Of The Product
2.2. Main components of the product N° Component Fork sleeves Safety locking pin Mounting plate for load hook with shackle Locking pin Locking hole Mounting hole for load hook Cotter pin Swivel hook Bow shackle 10 Support 8/32... -
Page 9: Placement Of The Decals
EXTENSIBLE ARM/BRAS EXTENSIBLE/ FIXED ARM/BRAS FIXE/FESTER ARM/BRAZO FIJO/VASTE ARM AUSZIEHBARER ARM/BRAZO EXTENSIBLE/ UITSCHUIFBARE ARM CAM ATTACHMENTS® Brabantstraat 15 • 8790 Waregem • Belgium T +32 56 43 42 11 • F +32 56 43 44 88 www.camattachments.com • info@camattachments.com Sticker_2ton_LABEL_062020_31601963.indd 1... -
Page 10: Type Plate
2.4. Type plate N° Explanation Manufactured outside the EU for: TVH PARTS HOLDING NV Address Brabantstraat 15 • 8790 Waregem • Belgium CE logo CAM attachments logo TYPE Type MODEL Model MODÈLE MODEL MODELL SERIENR. Serial number ° SÉRIE SERIAL NBR... -
Page 11: Safety Instructions
SAFETY INSTRUCTIONS 3.1. Explanation of the safety decals • Make sure that all the safety messages are legible. • Replace damaged stickers asking the manufacturer for new ones. • If the part to be replaced bears a sticker, ensure that a new sticker is applied to the new part. Crushing hazard (REF 162TA9232). -
Page 12: General Safety Instructions
In the event that equipment, procedures, work methods or working techniques are used that are not specifically advised by the CAM attachments company, it is necessary to make sure that there is no danger to the operator or other people. -
Page 13: Transport And Storage
TRANSPORT AND STORAGE 1. Storage The crane jib must always be stored in a dry and temperature-controlled environment. Avoid direct sunlight. Do not store this product outside in a wet environment. Store the crane jib in a safe place and make sure it cannot fall over. Lubricate the metal parts with an anti corrosion agent (REF 166TA1570 or REF 143TA6901). - Page 14 2. Transport If you want to transport the telescopic fork-mounted crane jib on a pallet, make sure that the attachment is securely attached so that it cannot fall off. Safely transport the crane jib by following the next steps: 1. Check the type plate to know the weight of the crane jib. Select the appropriate material according to the weight (ropes, cables, hooks, etc.).
-
Page 15: Assembly And Installation
• The assembly and installation must be carried out by an expert. • Make sure that the goods and packaging are in good condition. • Before commissioning, carry out a risk analysis on the assembly of the CAM attachment with the forklift. - Page 16 4. Choose the appropriate hoist hole (1–6) and attach the bow shackle in combination with the swivel hook onto the crane jib. 16/32...
-
Page 17: Commissioning
COMMISSIONING • The lifting device with attachment installed needs to be approved for use prior to commissioning. • Be sure to obtain the manufacturer’s certification concerning the residual capacity of the lifting device, after installing the attachment. • Provide a capacity table within sight of the driver from the lifting device. 6.1. -
Page 18: Extending The Crane Jib
6. Install locking pin (C) and secure it with (D). Your fork-mounted crane jib is now ready for use. After the assembly of the attachment and before putting the device into operation, check if all the functions work correctly. Any failure of the safety devices can cause malfunctioning and damage to the attachment. 6.2. -
Page 19: Operation
• For safety reasons, arbitrary adaptations or modifications to the equipment are prohibited. • In the event of non-envisaged workmanship or intervention or following a procedure different to that indicated in the manual, consult CAM attachments before proceeding in order to ascertain its feasibility. -
Page 20: Operating Instructions
7.2. Operating instructions Please see chapter 8 for the daily maintenance schedule. Perform the daily maintenance check before each use as described in chapter ‘8.3. Maintenance instructions’ . 1. Attaching the load 1. Follow the steps in chapter 5. ‘Assembly and installation’ to install the bow shackle + load hook. 2. -
Page 21: Maintenance
MAINTENANCE A telescopic fork-mounted crane jib is a lifting device. Comply with the obligation to perform periodic inspections if required according to national legislation. 8.1. Safety instructions for the repair of the product • The operator should wear safety shoes and gloves when using or maintaining the telescopic fork-mounted crane jib. - Page 22 3. Cleaning Only clean the equipment with a cloth dampened in a soap solution (REF 131TA5500)* or TotalSource wipes (REF 147TA3378). Do not use solvents, petrol, strong detergents etc. If the equipment is heavily soiled, the use of a pressure cleaner is only permitted providing that it is set to a maximum of 200 bar.
-
Page 23: Troubleshooting
TROUBLESHOOTING N° Problem Cause Action Damaged swivel Frequent or improper use. Replace the swivel hook or bow shackle hook/bow shackle. with a new one. See chapter 5. ‘Assembly and installation’ for assembling the bow shackle and swivel hook. See spare parts list for the correct reference Not possible to Wrong swivel hook. -
Page 24: Final Decommissioning And Disposal
FINAL DECOMMISSIONING AND DISPOSAL Final, proper decommissioning or disposal of the product must be performed in accordance with the regulations of the country in which the product is used. In particular, regulations governing the disposal of batteries, fuels and electronic and electrical systems must be observed. Waste packaging should be sorted and put into solid dustbins according to the materials and be collected by the local special environmental protection bureau. -
Page 25: Annexes
ANNEXES 11.1. CE-certificate 25/32... - Page 26 26/32...
-
Page 27: 11.2. Spare Parts List
11.2. Spare parts list 1. BA52820 Photo Description Reference 2T jib 166TA8157 Linch pin 106TA6976 Bow shackle with safety pin 134TA8279 Linch pin 106TA6975 Cotter pin 106TA6982 Siwvel hook with safety latch 143TA6394 Locking pin 166TA3452 Contact your dealer Locking pin with chain 166TA8158 27/32... - Page 28 2. BA52824 Photo Description Reference 4T jib 166TA8159 Linch pin 106TA6976 Bow shackle with safety pin 134TA8282 Linch pin 106TA6975 Cotter pin 106TA6982 Swivel hook with safety latch 143TA6396 Locking pin 166TA3452 Contact your dealer Locking pin with chain 166TA8158 28/32...
- Page 29 NOTES ................................
- Page 30 NOTES ................................
- Page 31 NOTES ................................
- Page 32 Your distributor: Manufactured outside the EU for TVH PARTS HOLDING NV. www.camattachments.com Agri info@camattachments.com Construction Industry Brabantstraat 15 Food & 8790 Waregem beverage Belgium Paper T +32 56 43 42 11 handling F +32 56 43 44 88...
Need help?
Do you have a question about the GAB2 Series and is the answer not in the manual?
Questions and answers