Advertisement
Quick Links
Distributed by Rock Drill Technologies
4442 Southward Dr. Olifantsfontein, Gauteng, RSA
Phone: +27 61 614 1844
www.loadhandler.co.za
LOADHANDLER® MODELS
LH2200 (full-size)
LH2200M (mid-size)
INSTRUCTION MANUAL
PLEASE READ ALL DOCUMENTS IN
THIS PACKAGE!
Although the Loadhandler® is a simple tool,
unloading heavy or bulky loads from your truck
can create unusual conditions. Please read all
documents to ensure the proper assembly and
operation of your Loadhandler®.
NEVER OVERLOAD YOUR VEHICLE.
IT IS DANGEROUS!
1
Advertisement
Related Manuals for LOADHANDLER LH2200
Summary of Contents for LOADHANDLER LH2200
- Page 1 LH2200M (mid-size) INSTRUCTION MANUAL PLEASE READ ALL DOCUMENTS IN THIS PACKAGE! Although the Loadhandler® is a simple tool, unloading heavy or bulky loads from your truck can create unusual conditions. Please read all documents to ensure the proper assembly and operation of your Loadhandler®.
- Page 2 LH2200 & LH2200M PARTS LIST: QTY ITEM DESCRIPTION Roller Bar Sections, including: (1) Left hand side* with slot for handle insertion (1) Middle section (both ends open for slugs) (1) Right hand side with red end cap * Left hand side is based on a person standing at the rear of the truck and looking towards the front of the vehicle Roller ‘slugs’...
- Page 3 NOTE: You only get 1 crank bar, depending on which model you purchase. Both crank bars are shown in illustration above for visual purposes only.
-
Page 4: Main Assembly
MAIN ASSEMBLY (Note that drawings show LHD vehicle arrangements) 1. Assemble the roller bar. Screw in slugs as far as they will go (half way) into both ends of the middle roller section. Screw in the driver (RHS) & passenger (LHS) roller sections as far as they will go. -
Page 5: Installation
INSTALLATION 1. With the crank slot on the left hand side, lower the Loadhandler® onto the upraised tailgate so that the tailgate is between the rubber pads on the inside of the brackets. 2. Slide the left hand side bearing bracket along the roller until near end of the tailgate, just clear of the inside wall of the truck bed. - Page 7 To Load Untie travel straps. Pull dragsheet from roller & lay on bed floor. (Bed liner or a Loadhandler® Double-Mat® should be used to unload 600kg or more.) Always leave 3-4 dragsheet wraps on the roller. Load truck. Open tailgate.
- Page 8 Before releasing handle or removing from the drive slot, relieve any tension on crank handle and Loadhandler®. Use the Loadhandler® as designed. Any modifications could adversely affect the functionality of the Loadhandler® and will void the warranty.
- Page 9 TO PREVENT THE ROLLER BAR FROM TURNING WHEN DRIVING WITH A LOAD Press the Velcro straps together to make one long strap. Feed one end of the long strap through the drive slot Wrap the strap around the bearing bracket projecting from the rear of the tailgate. 4.
-
Page 10: Important Notice
A sheet of hard plastic, linoleum, wood paneling, etc. all work well. Or consider purchasing the Doubl-Mat® by Loadhandler Products, a reversible mat that is both a "slip-liner" on one side and a protective, non-slip rubber mat on the other side. - Page 11 If your truck/LDV bed is rusty, or has a non-slip spray-in liner, you must have the Doubl- Mat® (or similar slip-liner) in order to use the Loadhandler®. If your pickup bed is in good shape or you have a plastic liner, you do not need the Doubl-Mat® when using the Loadhandler®.
-
Page 12: Month Limited Warranty
You have purchased the 2200 Series Loadhandler® LH2200 (full-size) or LH2200M (mid-size) unit. Please call Rock Drill Technologies directly with any warranty situations, replacements, or lost parts at +27 61 614 1844 or visit our website at www.loadhandler.co.za...