Table of Contents
Advertisement
8 | English
(6) Orbital stroke rate preselection thumbwheel
(7) Pivoting feet
(8) Recess for pivoting feet
(9) Square base plate with clamp fastening
(10) Square foam pad hook-and-loop fastening
(11) Screws for base plate (x4)
(12) Rectangular base plate
(13) Rectangular foam pad hook-and-loop fastening
(14) Triangular base plate
(15) Triangular foam pad hook-and-loop fastening
(16) Handle (insulated gripping surface)
(17) Sanding sheet with hook-and-loop fastening
(18) Front clamping bracket
(19) Sanding sheet clamps (x2)
(20) Rear clamping bracket
(21) Extraction outlet
(22) Dust bag
(23) Adapter for dust bag
a)
(24) Extraction hose
(25) Punch
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Orbital sander
Article number
Rated voltage
A)
No-load speed
A)
No-load orbital stroke rate
Orbit diameter
Sanding plate dimensions
– Square
– Rectangular
– Triangular (sanding sheet
length from corner to
corner)
Weight according to EPTA-
B)
Procedure 01:2014
Recommended ambient
temperature during charging
Permitted ambient temper-
C)
ature during operation
and
during storage
Recommended rechargeable
batteries
1 609 92A 73N | (29.06.2022)
GSS 10.8V-13
3 601 JL0 0..
V=
10.8
–1
min
6000–10,000
–1
min
12,000–20,000
mm
1.6
mm
100 x 110
mm
80 x 130
mm
100 x 150
kg 1.0 kg (1.5 Ah)–1.2
kg (6.0 Ah)
°C
0 to +35
°C
–15 to +50
GBA 10.8V...
Orbital sander
Recommended chargers
A) Measured at 20–25 °C with rechargeable battery
GBA 10,8V 2.0Ah.
B) Depends on battery in use
C) Limited performance at temperatures < 0 °C
Rechargeable battery
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
The rechargeable battery has two locking levels to prevent
the battery from falling out if the battery release button is
pressed unintentionally. The rechargeable battery is held in
place by a spring when fitted in the power tool.
Battery charge indicator
The battery charge indicator (5) on the power tool consists
of three green LEDs. It indicates the battery's state of charge
for a few seconds after the power tool is switched on and off.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slowly flashing light 1 x green
The three LEDs in the battery charge indicator flash
quickly when the temperature of the battery is outside
the operating temperature range of -30 to +70 °C and/or
the overload protection has been triggered.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
GSS 10.8V-13
GAL 12...
GAX 18...
Capacity
60–100%
30–60%
10–30%
0–10%
Bosch Power Tools
Advertisement
Table of Contents
