5.3 Replacing parts
All parts must be replaced by authorized technicians
only!
To replace the following parts first remove all the control knobs and
control panel (after loosening the fixing screws), then extract the
ignition wire.
5.3.1 Gas cock
Loosen the gas piping and thermocouple hoses (pos. 17 and 16 fig.
1), then loosen the screws fixing the gas supply (pos. 21 fig. 1) to the
gas ramp and insert a new tap. After the replacement check the seal
using a leack detetctor spray.
5.3.2 Thermocouple
Loosen the screw couplings fastening the thermocouple to the gas
tap (pos. 17 fig. 1) and pilot burner (pos. 19 fig. 3); insert the new
part. After replacing the parts, fit the control panel and its parts
back in the right order.
5.3.3 Plug
The spark plug (pos. 16 fig. 3) can be removed after opening the
flame support by unscrewing the fastening screws (pos. 19 fig. 3).
Disconnect the starter cable and insert a new spark plug.
5.3.4 Burner
Unscrew the injector-holder nut (pos. 29 fig. 2) and pull off the injec-
tor-holder (pos. 28 fig. 2). Lift up the burner (pos. 27 fig. 2) for pull
off from the injector-holder, pull off and put in a new piece in the
reverse order. After the replacement check the seal using a leack
detector spray.
6.1 Safety, cleaning and repair rules
• This appliance is used for the preparation of meals at industri-
al level. Usage and cleaning can be carried only by expert per-
sonnel. Maintenance and repair can be carried out only by
skilled technical personnel.
• These indications must be communicated to all those con-
cerned during internal training.
• Attention! This appliance must be constantly watched over
when being used!
• Grease and overheated oil can catch fire. Use this appliance
only under constant control. Never use water to put out
grease or oil!
• Do not leave the burners running.
• Parts of the appliance and attachments exposed to food
must be cleaned with detergents and rinsed thoroughly with
potable water.
• Do not clean the appliance using water jets or steam,
whether direct or pressurized!
• If the room is being cleaned with water/steam jets or high-pres-
sure equipment, it is necessary to switch off the appliance first!
• Before starting to clean the appliance, disconnect from the
mains.
• Do not use inflammable liquid to clean the appliance.
• Repairs may be carried out only by skilled personnel.
• During repairs, the appliance must undergo voltage
omnipolar insulation (local switch, i.e. safety load cut-off
0814_GB_42 - BARBECUES LAVA STONE
5 - SET-UP FOR OPERATION
6 - INSTRUCTIONS FOR USE
6.2 Start-up
6.2.1 Lighting pilot burner
Press the knob (pos. 1 fig. 4) and turn to the left as far as
Keep the knob pressed down while repeatedly pressing the piezo
ignition button (pos. 2 fig. 4) until the pilot flame catches, you can
see through aperture on the control panel that the flame has cau-
ght. Keep the knob pressed down for another 15-20 seconds: if the
pilot flame goes out after the knob is released, start again.
9 · 12
After any maintenance or repair work, replace the con-
trol panel and the lower panel.
After replacing gas input components, check operation
again and test for leakage.
switch).
• Noise emission values of the appliance in operation are
below 70dB (A). This value is compulsory according to certain
national safety standards.
WARNING
Attention! The manufacturer declines all responsibility concern-
ing mistakes included in these instructions due to translating or
printing errors: the manufacturer also reserves the right to
change the product as he see fits, though without changing its
essential features. The manufacturer declines all responsibility
for any non-compliance with the provisions contained in this
manual.
Before using the appliance for the first time, thorou-
ghly clean the grid with lukewarm water and deter-
gent, using a soft cloth to eliminate all trace of the
rust-proofing applied in the workshop. Dry with a
clean cloth.
.
04/2008