Related Manuals for Quick 492G Series
Summary of Contents for Quick 492G Series
- Page 1 QUICK 492G Series Combo Tester Instruction Manual Thank you for purchasing our products. Please keep the instruction manual properly for future reference.
-
Page 2: Table Of Contents
Contents 1. Safety Instructions................1 2. Overview....................2 3. Product Characteristics............... 2 4. Product Specifications.................3 5. Functional Descriptions...............4 5.1. Dimensions................4 5.2. Part Descriptions..............5 6. Connection.................... 6 7. Parameter Settings................7 7.1. Password Settings..............7 7.2. Wrist Strap and Anti-static Shoes Settings......8 7.3. -
Page 3: Safety Instructions
1.Safety Instructions CAUTION During the installation and use of this product, all electrical safety regulations of the country and regions must be strictly observed. If the product does not work properly, please contact the supplier or our company, and do not disassemble or change the product in any way. -
Page 4: Overview
2.Overview The combo tester can quickly test the grounding situation of workers, whether the wearing of single-wire wrist strap, dual-wire wrist strap, anti-static shoes, foot rings and shoe covers conforms to the standard of static protection ANSI/ESD-S20.20-2021, the measurement range is 100KΩ... -
Page 5: Product Specifications
4.Product Specifications Product model With With With Support Support With Support column. column. Support Configuration column. column Large Small Large Small fixed fixed fixed plate fixed plate plate. plate. Working model On-line Stand-alone AC coupling adapter Power supply DC 8-12V Voltage：±400V（Max）（Peak value，DC or AC）... -
Page 6: Functional Descriptions
5.Functional Descriptions 5.1.Dimensions Unit：mm... -
Page 7: Part Descriptions
5.2.Part Descriptions... -
Page 8: Connection
6.Connection Note: GND must be connected to ground. The two AGNDs in the six- core connector are used to connect the anti-static shoes pedal to the shielding end of the tester shielding line, and must not be connected to the GND of the three-core connector. -
Page 9: Parameter Settings
7.Parameter Settings Press the tester screen for 3 seconds to enter the setting interface. As shown in Figure 1： Figure 1 7.1.Password Settings On the password page, you can set the parameters. If you do not input the password, you can only view the setting parameters of the tester. The default password is: 00000000. -
Page 10: Wrist Strap And Anti-Static Shoes Settings
7.2.Wrist Strap and Anti-static Shoes Settings 1）The wrist page has the options of enabling wrist straps and dual-wire wrist straps, which can be selected as required (as shown in Figure 3). The anti-static shoes page only has the anti-static shoes enabled option, which can also be selected as required. -
Page 11: Other Interface Settings
7.3.Other Interface Settings 1）Communication address-It can be set at will in stand-alone mode. In online mode, it is necessary to ensure that all online devices don't have duplicate addresses. 2）Language selection-Simplified Chinese, Traditional Chinese and English are supported. 3）Working mode-support online and stand-alone selection. 4）Access control signal-enable to open the door and enable to close the door. -
Page 12: Calibration Settings
7.4.Calibration Settings 1) Press the touchscreen calibration button to follow the prompts to calibrate the touchscreen. If the cursor position is abnormal, press and hold the screen first, then turn on the power supply of the tester, and then press the reset button in the small hole on the right side of the tester with an insulating stick to initialize calibration of the touchscreen. -
Page 13: Test Instructions
8.Test Instructions 1) Keep good contact between the hand and touch switch during the test. 2) Do not do strenuous exercise during the test to avoid static electricity or poor contact, resulting in unstable test data. 3) Do not use the tester in an environment with unstable voltage or strong electric field to prevent inaccurate test results. -
Page 14: Calibration
10.Calibration 10.1.Calibration Parameters Each channel shall be tested with a standard resistance, and all tests shall meet 10% accuracy. If the range is exceeded, the tester shall be calibrated again. 10.2.Calibration Method If the calibration is required, please use the calibration equipment provided by our company. - Page 15 12-month warranty period. Serial No.: ●Please keep this warranty card properly. It will not be re-offered after. Delivery Date: QUICK INTELLIGENT EQUIPMENT Address : CO., LTD. ADD: NO.11, FengXiang Road, Wujin Postcode: High-Tech Industrial Development...
- Page 16 QUICK INTELLIGENT EQUIPMENT CO., LTD. ADD: NO.11, FengXiang Road, Wujin High-Tech Industrial Development Zone, Jiangsu, China TEL: 86-519-86225678 FAX: 86-519-86558599 POSTCODE: 213167 WEBSITE: www.quick-global.com...
Need help?
Do you have a question about the 492G Series and is the answer not in the manual?
Questions and answers