1. Manuals
  2. Brands
  3. S2 Manuals
  4. Network Hardware
  5. NetBox Enterprise
  6. Install and setup manual

S2 NetBox Enterprise Install And Setup Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Integrated security for an IP-connected world
S2 NetBox Enterprise™ and Enterprise Ultra™
Install and Setup Guide
Configuring Your S2 NetBox Enterprise .......................................................... 2
Connecting Power and the Network to the NetBox Enterprise................................................... 2
Configuring IP Settings ............................................................................................................... 3
Logging in to your NetBox Enterprise ......................................................................................... 4
Connecting Nodes and Configuring System Resources ............................................................ 4
Specifications ..................................................................................................... 6
Front Panel LEDs........................................................................................................................ 6
Reset Switches and Drive Lights ................................................................................................ 7
The NetBox Enterprise Hard Drives ........................................................................................... 8
Migrating from NetBox 3.1 to NetBox Enterprise 3.1 ...................................... 9
Contents
Version 3.1
S2 Security Corporation
50 Speen St. Suite 300
Framingham, MA 01701
www.s2sys.com
S2 Support: 508 663-2505
1

Advertisement

Table of Contents
loading

Summary of Contents for S2 NetBox Enterprise

  • Page 1: Table Of Contents

    Install and Setup Guide Contents Configuring Your S2 NetBox Enterprise ............2 Connecting Power and the Network to the NetBox Enterprise........... 2 Configuring IP Settings ....................... 3 Logging in to your NetBox Enterprise ..................4 Connecting Nodes and Configuring System Resources ............4 Specifications .....................

  • Page 2: Configuring Your S2 Netbox Enterprise

    The back panel of the NetBox Enterprise, 1U rack mount. The back panel of the NetBox Enterprise Ultra, 2U rack mount. 3. For the NetBox Enterprise Ultra (2U), open the drive door on the front panel and press the power switch. See diagram below.

  • Page 3: Configuring Ip Settings

    2. You can edit any of the settings on this page. NOTE: If you change the IP address of the NetBox Enterprise be sure to take note of the new address as you will need it to log in later.

  • Page 4: Logging In To Your Netbox Enterprise

    Enter. The IP setting changes that you have made are now saved to the NetBox Enterprise. 8. Repeat steps 5 through 8 to make any further changes to the NetBox Enterprise IP settings. 9. Use the arrow keys to highlight Exit and press Enter.
  • Page 5 9. If any nodes are not yet connected to the NetBox Enterprise controller, return to step 1 in this procedure and ensure that all nodes are enabled. 10. If some nodes still will not connect it may be necessary to adjust port forwarding on routers and gateways to allow the nodes on different subnets to communicate with the controller.

  • Page 6: Specifications

    S2 NetBox controller. The S2 Security NetBox Enterprise Ultra is a 19” 2U rack mount network appliance that gives you maximum capacity for applications of greater scale and complexity.

  • Page 7: Reset Switches And Drive Lights

    System This button restarts the NetBox Enterprise controller processes. Reset The NetBox Enterprise has an audible alarm which sounds when the Alarm Reset power, temperature, or the fan are in an abnormal state. Press this to stop the audible alarm.

  • Page 8: The Netbox Enterprise Hard Drives

    This will unseat the drive. 9. Pull the drive out of the NetBox Enterprise Ultra. 10. Place the new drive into the NetBox Enterprise Ultra and press the drive level all the way in until it snaps into position.

  • Page 9: Migrating From Netbox 3.1 To Netbox Enterprise 3.1

    1. Connect power and the network to the NetBox Enterprise. 2. Open the drive door on the front panel of the NetBox Enterprise and press the power switch. The NetBox XL may need 2 to 3 minutes to launch.
  • Page 10 NOTE: The default IP address of a NetBox Enterprise is 192.168.0.250. If you changed this in previous steps then enter the new address here. 4. At the Login page enter the User name “admin.” 5. Enter the Password “admin.” 6. Click Go. The security application will now display.
  • Page 11 8. If any nodes are not yet connected to the NetBox Enterprise controller, return to step 1 in this procedure and ensure that all nodes are enabled. 9. If some nodes still will not connect it may be necessary to adjust port forwarding on routers and gateways to allow the nodes on different subnets to communicate with the controller.

This manual is also suitable for:

Enterprise ultra

Table of Contents