1. Manuals
  2. Brands
  3. Loreme Manuals
  4. Media Converter
  5. CPL36 R1 Series
  6. Configuration handbook

Loreme CPL36 R1 Series Configuration Handbook

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Hardened TRMS converter for AC and DC signals
Wattmeter, Voltmeter, Ammeter,....
CONFIGURATION HANDBOOK
CPL36
LOREME 12, rue des Potiers d'Etain Actipole BORNY - B.P. 35014 - 57071 METZ CEDEX 3
Phone 03.87.76.32.51
Contact : Commercial@Loreme.fr - Technique@Loreme.fr
Download manual at : www.loreme.fr
REV 0.1 - 16/01/19
E 1

Advertisement

Table of Contents
loading

Summary of Contents for Loreme CPL36 R1 Series

  • Page 1 Hardened TRMS converter for AC and DC signals Wattmeter, Voltmeter, Ammeter,…. CONFIGURATION HANDBOOK CPL36 LOREME 12, rue des Potiers d'Etain Actipole BORNY - B.P. 35014 - 57071 METZ CEDEX 3 Phone 03.87.76.32.51 Contact : Commercial@Loreme.fr - Technique@Loreme.fr Download manual at : www.loreme.fr...
  • Page 2 2.3) Inputs / Outputs ........................... p13 WIRING ..................................p14 WIRING EXAMPLES ..............................p15 Hall sensor current input ..........................p15 Shunt current input ............................p15 BIPOLAR OUTPUT WIRING ............................ p16 LOREME 12, rue des Potiers d'Etain - 57071 Metz  03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr...

  • Page 3: Device Presentation

     CPL36../R2 : + 2 relays.  CPL36../S2 : 2 analog outputs. The technical data sheet is downloadable here: http://www.loreme.fr/fichtech/CPL36_eng.pdf Green power LED Configuration access YES button 4 digits alphanumerical display Increment button (+) R1 & R2 alarms state signaling LEDs...
  • Page 4 For an AC signal the average value is 0. Signal with an average value < 0. Signal with an average value > 0. +100 -100 V LOREME 12, rue des Potiers d'Etain - 57071 Metz  03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr...
  • Page 5  TABLE OF CONTENTS The next 2 rubrics are only accessible if the ALTERNATIVE mode was previously selected SINGLE PHASE? Push the YES button to choose the single phase mode or the NO button to select the next choice. THREE PHASES? Push the YES button to choose the three phases mode with neutral.

  • Page 6: Decimal Point

    If, during the configuration process, no buttons are pressed for more than 90 s, the device returns to measure mode without saving the new configured parameters. LOREME 12, rue des Potiers d'Etain - 57071 Metz  03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr...

  • Page 7: Rs232 Link Setting

    Step 2: Setting of terminal emulation software (PC with windows). The terminal emulation software for PC « HyperTerminal » is resident in windows up to XP version. For later ver- sions, it is downloadable on : www.loreme.fr in download part ( http://www.loreme.fr/HyperTerm/htpe63.exe =>...

  • Page 8: Terminal Mode

    - In configuration mode, if you want go back to measure mode without taking notice of modifications made before, just press the escape key. LOREME 12, rue des Potiers d'Etain - 57071 Metz  03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr...
  • Page 9  TABLE OF CONTENTS Configuration 2.2) Language The language possibilities are: - French - English 2.3) Input The input configuration is made of: - Measure response time. 2.4) Network The wiring options on the network are: - Alternative TRMS (AC+DC) or continuous (DC) (only on standard or Hall version). - Single-phase or balanced three phases with neutral.
  • Page 10 Press ‘Y’ and ‘Enter’ to lock the front face configuration access. BIPOLAR OUTPUT? (Y-N)NO Press ‘Y’ and ‘Enter’ to activate the bipolar +/-10 V output. E 10 LOREME 12, rue des Potiers d'Etain - 57071 Metz  03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr...
  • Page 11  TABLE OF CONTENTS 2.9) End of the configuration This message indicates that all the parameters have been successfully saved. Remark: If no action is performed during the configuration process, the device returns automatically to measurement mode after a wait of two minutes, without taking into account of the modifications made before. E 11...

  • Page 12: Firmware Update

    FIRMWARE LOADER Rev3 READY TO TRANSFER... The device is now in the firmware load mode and is waiting for the firmware file. This file is provide by LOREME and contain the firmware code in Intel HEX format. Select the « Transfer », « Send a text file ... » in the HyperTerminal menu.

  • Page 13: Emc Consideration

    1) Introduction To meet its policy concerning EMC, based on the Community directives 2014/30/EU & 2014/35/EU, the LOREME company takes into account the standards relative to this directives from the very start of the con- ception of each product. The set of tests performed on the devices, designed to work in an industrial environment, are made in accor- dance with IEC 61000-6-4 and IEC 61000-6-2 standards in order to establish the EU declaration of confor- mity.
  • Page 14 Vin, Gnd for the signal. terminals +15V & -15V for the sensor power supply. Rogo version Rogowski sensor input: terminals 200mV, 0mV/0A. E 14 LOREME 12, rue des Potiers d'Etain - 57071 Metz  03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr...

  • Page 15: Wiring Examples

    For a CPL36-Hall with Hall sensor current input User Power supply device (or AC) Hall effect sensor of type Hco with its cable, furnished by LOREME For a CPL36 with external shunt current measurement Neutral User Shunt XX A device...
  • Page 16  TABLE OF CONTENTS Bipolar output Wirings +/- 10 V output E 16 LOREME 12, rue des Potiers d'Etain - 57071 Metz  03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr...

This manual is also suitable for:

Cpl36 r2 seriesCpl36 s2 seriesCpl36Cpl36-rogoCpl36-hall

Table of Contents