Advertisement
2. ASSEMBLY & SPECIFICATIONS
The dAS150T.V3 and dAS150T/dFS.V3 have alloy gear housings and
composite motor housings. Both units have slider On/Off switches with
power lock. discs and pads for dAS150T/dFS have holes through which
dust is extracted. This unit must be connected to a dust
extraction system. Contact your Sealey dealer for details. DO NOT use a
standard vacuum cleaner to extract dust as damage to the cleaner may
result.
2.1.
Assembly
WARNING! DO NOT plug sander into the mains power supply before
it is fully assembled.
Unpack the sander and check contents against figure 1. The contents
should include a spanner and hex key. Should there be any damaged or
missing parts contact your supplier immediately. Screw handle (2) into
the hole (right or left side, as required) in the head. Screw the sanding
pad onto the spindle (3). To remove pad, hold spindle with the spanner
supplied whilst unscrewing the pad. The Hex key is for removal of the
eccentric shaft for cleaning etc. and is inserted at point (4).
2.2.
Specification: DAS150T.V3 & DAS150T/DFS.V3
Power . . . . . . . . . 230V - 400W
No load speed . . . . . . 7000rpm
Orbit size . . . . . . . . . . . . 8 mm
Pad . . . . . . . . . . . . . . .Ø150mm
Thread . . . . . . . . . . . 5/16"UNF
Weight . . . . . . . . . . . . . . 2.2 kg
Vibration . . . . . . . . . . 21.15m/s²
Sound power level . . . . 90.7dB
Sound pressure . . . . . . 79.7dB
Note: dAS150T.V3 may be converted for use with dust free systems
using kit Model No. dFS/ACC4. Contact your Sealey dealer for details.
(See fig.2)
3. OPERATING INSTRUCTIONS
WARNING! Before use, ensure that you have read and understood
Section 1 Safety Instructions.
3.1.
Attach the correctly rated sanding disc (not supplied) to the
sanding pad.
3.2.
Plug the sander into the mains power supply.
3.3.
Grip the side handle and turn on by pushing switch (fig 1.1)
forward. let go of the switch and the machine will continue
running.
3.4.
To release the switch, and stop the sander, press down
on the rear section of the switch - it will spring to the Off
position.
3.5.
Check that the unit is working correctly before use.
Note: The sander is designed for dry use only. DO NOT use with water
or any other liquids.
4. MAINTENANCE
WARNING! Disconnect sander from power supply before changing
accessories, servicing or performing maintenance. Replace or
repair any damaged parts. Use genuine parts only, unauthorised
parts may be dangerous and will invalidate the warranty.
4.1.
After each 50 hours use (or as required), remove dust by blowing
air through the side vents and around the pad bearing. Periodic
cleaning will prolong machine life.
4.2.
Change pads when required. ensure pad and disc RPM ratings
are equal to, or exceed the machine rating. If the disc becomes
unbalanced, it will cause the bearings to wear.
4.3.
When not in use store in a safe, dry, childproof location.
4.4.
Check brushes every 200 hours of use. To access the brushes
refer to fig.3. Undo the screw in the end of the motor casing (1)
and slide back the cover (2). Using a small screwdriver lift the
brush spring to one side (3) and slide the brush out of its holder (4).
If the brush is worn to half of its original length it should be renewed.
Using thin nosed pliers pull the brush connector off its terminal (5).
Slide the new brush into its holder. Slide the connector onto the
terminal (5). Position the spring so that it bears down onto the
end of the brush. Remember to renew brushes as a pair. Slide
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
PADS: DAS150T.V3
Pad No. PTC/150A Stick-on (Firm)
PTC/150SA (supplied) Stick-on(Soft)
PTC/150VA . . . . . . . Hook & loop
PADS: DAS150T/DFS.V3
Pad No. AK289 Stick-on (supplied)
or AK290 . . . . . . . . . Hook & loop
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. edmunds, Suffolk,
IP32 7AR
Original Language Version
rear cover back into place and retain it with the screw.
4.5.
All other service and maintenance must be carried out by an
authorised service agent.
01284 757500
01284 703534
dAS150T.V3, dAS150T/dFS.V3
fig. 1
fig. 2
fig. 3
www.sealey.co.uk
Web
sales@sealey.co.uk
email
Issue: 3 - 05/01/10
Advertisement
