Leader Light LL IN8-RSxxx, LL08 300 xxx - Potential Free Contact Module Manual

Overview of the unit

* LL08 300 xxx
xxx - protocol type 0v3, or 0v4, or 0v5

All dimensions are in millimeters

Package includes:

• LL IN8-RSxxx 1 pc.
• User manual 1 pc.

Additional items needed:

• Data and power cables
• 24V DC power supply

ENVIRONMENTAL PROTECTION

Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment.

SAFETY INFORMATION

Carefully read before installing, powering or servicing. Nothing to do if anything misunderstand! Installation can be done only by a qualified professional in accordance with relevant local codes.

Safety instructions

• Shut down power before installation or maintenance of equipment or voltage /data source.
• Do not modify, alter, or attempt to service the LeaderLight appliance. Doing so will void the warranty.
• Use only the recommended DC voltage source.
• Connect the ground to the bottom of the box!
• Electrical connections, service and maintenance can be performed only by qualified professional.
• AC power supply of DC power supply must comply with local regulations.
• AC power supply must be protected against overvoltage and short circuits.

Operating restrictions

• This product was designed for indoor use only!
• If the product has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.
• Do not operate the product in humid, dusty or too hot/cold environments.
• Before connecting, make sure the product is not damaged, wet, or otherwise damaged.
• Unprofessional operation creates the most damages!
• For transport use the original packaging.

Operate only with 24V DC stabilized source!

Fire protection

• Follow all safety restrictions.
• Device never cover – the minimum space around the vents must be at least 100mm (4 in.).
• Allowed maximum ambient temperature is 40°C (104°F).

PRODUCT SPECIFICATION

Technical specification

Product description

Indication of control LED (LED power / data - yellow)

INSTALLATION

Unpacking

• Unpack carefully.
• This is electronic equipment and should be handled carefully.
• Damaged delivered package or if are any mechanical parts broken – it must be claim immediately by the transport company. Photo pictures as evidence are valuable for future claim.

Physical installation

• Loading capacity of bearing area has to be at least 10 times the weight of all device clusters.

Connection

• Respect all SAFETY INFORMATION!
• Connect the ground (earth) to the bottom of the module!
• LL IN8-RSxxx device may be operated only with 24V DC stabilized source.
• In the case of connecting the power supply with more than a prescribed voltage you can suffer a dangerous electric shock, inflict damage equipment or fire.
• Shut down power supply from all devices before installation of LL IN8-RSxxx to end devices.

If you have any question please, contact support@leaderlight.sk

Wiring diagram of LL IN8-RSxxx module

Connecting with potential free contacts.

The voltage outputs, in combination with potential free contact.

Connecting with galvanic inputs separation with using an external source.

Feature LL IN8-RSxxx

LL IN8-RSxxx is input device. It includes 8 digital inputs, which can be switched with any contact.
The input module is designed as an interface for connecting any arbitrary button control to the control system RS digital output protocol of the sending state inputs can be varied.

Installation Factors

• For any indoor and outdoor installation inside the installation box must be add +100mm to each side and must be add ventilation modul.
• For outdoor installation must be add heating modul, if the outdoor temperature is less then 0°C any time!

RSX channels

These informations are subject to change, latest data are on: www.leaderlight.eu

Mode1:
Input In1 = commands ASCI Output1
Input In2 = commands ASCI Output2
Input In3 = commands ASCI Output3
Input In4 = commands ASCI Output4
Input In5 = commands ASCI Output5
Input In6 = commands ASCI Output6
Input In7 = commands ASCI Output7
Input In8 = commands ASCI Output8

Features Dip ( switch Dip1, Dip2, Dip3, Dip4 ):
Dip1 = On = without function
Dip2 = On = without function
Dip3 = On = without function
Dip4 = On = without function

Sending ASCII commands are set by the RSX protocol. Currently available are the following protocols:
I8 0v3: protocol ASCIout 0v3 (6Byte)
I8 0v4: protocol ASCIout 0v4 (4Byte) – E-cue
I8 0v5: protocol ASCIout 0v5 (9Byte) – Creator
Description of the protocol is attached.

MAINTENANCE AND SERVICE

• Before any maintenance is necessary to carefully read all SAFETY INFORMATION!
• Damages caused by inadequate cleaning or maintenance are not covered by warranty.
• Requires periodic cleaning (dust, dirt,...)

Procedure for maintenance:

• Unplug mains before maintenance and at least 10 minutes cool off.
• Appliance do not illegal open or demount.
• Clean-up dust only from outer surface. Use vacuum or dumpy duster (warm water)
• Before reinstalling make sure everything is intact and dry– no wet parts!

Service:
Customer service provided by the manufacturer.

If you have any question please, contact support@leaderlight.sk

Leader Light s.r.o.
M.Gorkeho 33
SK-052 01 Spisska Nova Ves
Slovakia
www.leaderlight.eu

©MMX - Leader Light – All right reserved

Documents / Resources

References

• LEADER LIGHT - professional lighting products

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Leader Light LL IN8-RSxxx, LL08 300 xxx - Potential Free Contact Module Manual