Advertisement
Quick Links
Advertisement
Summary of Contents for Timewatch TWLD-TS2700
- Page 1 Manual Semi-Automatic Turnstile Gate TWLD - TS2700...
-
Page 2: Matters Needing Attention
Matters Needing Attention The internal wiring of this product has been completed when leaving the factory. Please do not change any wiring except what has been done in this manual Instructions. The company is not responsible for any damage caused by unexplained alterations. The casing must be grounded, and installed in the power supply end leakage protection switch. - Page 3 Directory 1. Introduction of channel gate products 2. Functional features of the channel gate 3. Technical parameters of the channel gate 4. Installation and debugging details 5. Composition and principle of channel gate equipment 5.1 Composition of channel gate products 5.2 System working principle 6.
- Page 4 1. Introduction of channel gate products Channel gate is the intelligent channel management equipment developed and produced by our company for many years. The device integrates mechanical, electronic, microprocessor control, and various reading and writing technologies. The appearance of the equipment adopts stainless steel plate laser welding molding, beautiful appearance, rust-proof, durable, and external use of standard electrical interface, can easily bar code card, ID card, IC card, and other card readers integrated into the equipment, to provide a civilized, orderly way of passage for people in and out, but also put an...
- Page 5 4. Installation and debugging details The hole reserved for connecting line is shown in the figure, which can be knocked off for wiring When the power is connected, press the pole in the direction of the arrow first. When you hear the sound of "da", it means that the magnet has been drawn and you can lift the pole.
- Page 6 5. Composition and principle of channel gate equipment 5.1 composition of channel gate products 5.1.1 Channel gate mechanical system Channel gate mechanical system is divided into chassis and movement of two parts. The chassis as a carrier, installed on the direction indicator light, read and write device, etc. The main components of the movement are the frame, drive shaft, rotating rod, and limit piece;...
-
Page 7: System Working Principle
S.No. The name of the function IC/ID card access control, fingerprint machine, Entrance guard face recognition, TWO-DIMENSIONAL code system equipment The control center of the system, it receives the signal of card reader and infrared sensor, Control panel and makes logical judgment and processing to these signals, and then sends the execution command to the direction indicator Direction... - Page 8 6. Installation and debugging of channel gate equipment 6.1. Installation of channel gate equipment Prepare tools for installing devices and check accessories according to the packing list. After completing the foundation surface of the installation equipment, arrange the equipment and make sure that the equipment is aligned horizontally. After locating the holes, drill the holes, and rebury the anchor bolts or expansion bolts of M12.
- Page 9 6.2. Functional debugging of channel gate equipment (Note: The gate machine of our company has been adjusted normally in the workshop according to the order requirements before leaving the factory. Now it is installed according to the requirements without debugging. For fine-tuning, please refer to the following parameter description and contact after-sales guidance.) 6.2.1 Key Description Control panel keys:...
- Page 10 F 0 6 Zero signal set; 0: Close the gate immediately upon detection of zero signal (three-roll gate standard mode, the default setting of the motherboard is 0)1: the zero signal is detected, and then wait for the zero signal to disappear before closing the gate (commonly used in full- height switching) 2: The gate is immediately closed when the zero signal is detected.
- Page 11 7. Troubleshoot common faults 7.1.Three roller brake does not open by swiping the card 1) Check whether the motherboard receives the opening signal 2) Check whether the opening signal line is loose and whether the solenoid valve line is loose; 3) After powering on the mainboard, manually press the button to see whether the limit chip can be unlocked normally 4) use a multimeter to measure whether there is 24V voltage output at the wiring port of the...
- Page 12 (+91)-11–41916615 sales@timewatchindia.com D-162, Okhla Phase-I, Okhla Industrial Area, +91 9609749609 New Delhi,110020 www.TimeWatchindia.com...
- Page 13 The above data are all decimal numbers. Parity code =(Synchronization code) XOR (device address) XOR (data 1)XOR(data 2) Ex. : Send the door opening instruction to a device whose address is00The sending command is: EB 00 50 00 BB The return command is : EB 00 D0 00 3B Head Office: D-162, Okhla Phase I,Okhla Industrial Area, New Delhi, 110020 Regional Offices: Mumbai, Bangalore, Ahmedabad,...
Need help?
Do you have a question about the TWLD-TS2700 and is the answer not in the manual?
Questions and answers