Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for RADWAG PM02.EX
- Page 2 NOVEMBER 2019...
- Page 3 PRECAUTIONS Prior to installation, use or maintenance activities, carefully read this user manual. Use the PM02.EX-*-* power supply only as intended. This user manual must be at a reach of the operator's hand in the course of the device operation.
-
Page 4: Table Of Contents
2. TECHNICAL SPECIFICATIONS ........................8 3. USAGE CONDITIONS ........................... 8 3.1. Electrostatic Charges Hazard ........................8 3.2. Output Parameters of PM02.EX-*-* Power Supply .................. 8 4. WARRANTY CONDITIONS ........................... 9 5. SECURITY REQUIREMENTS ........................9 5.1. ATEX Marking – Symbols Meaning ....................... 11 5.2. -
Page 5: Intended Use And Design
1. INTENDED USE AND DESIGN The PM02.EX-*-* power supply is equipped with intrinsically safe output circuits. This device is powered from the mains of the following voltage: 100÷240V AC. It is an associated facility for permanent installation, intended to supply with power intrinsically safe devices, including PL.*.*.HRP.EX.* weighing platforms. - Page 6 PM02.EX-*-* power supply marking Due to the place of power supply installation and the method of connecting intrinsically safe output circuits, the versions of PM02.EX-*-* power supply are marked in accordance with the coding method presented below. PM02.EX-*-* The method of connecting intrinsically safe output circuits: 1.
- Page 7 Installation option - 2: PM02.EX-2-* power supply intended for operation in safe area, the intrinsically safe circuits are led to the hazardous area. Hazardous area EX DEVICE PM02.EX-2-* Fig.3. Power supply in safe area PM02.EX-*-* – power supply – overall dimensions:...
-
Page 8: Technical Specifications
It is not allowed to use the power supply in places where mechanisms causing electrostatic charges greater than those caused by rubbing the surface by hand occur. 3.2. Output Parameters of PM02.EX-*-* Power Supply Circuit mark 1 µF 89 µH 7.60 V... -
Page 9: Warranty Conditions
4. WARRANTY CONDITIONS A. RADWAG feels obliged to repair or exchange all elements that appear to be faulty by production or by construction. B. Defining defects of unclear origin and means of their elimination can only be realized with the assistance of the manufacturer and the user representatives. - Page 10 II [2]D [Ex ib Db] IIIC. Explosion safety of PM02.EX-*-* power supply is ensured by: PM02.EX-*-* power supply is compliant with: PN-EN IEC 60079-0, PN-EN 60079-11, PN-EN 60079-7, PN-EN 60079-18, PN-EN 60079-31, PN-EN 60529 confirmed by OBAC 19 ATEX 0215X,IECEx OBAC 19.0010X certificates.
-
Page 11: Atex Marking - Symbols Meaning
5.1. ATEX Marking – Symbols Meaning Equipment group: Max surface temperature: Electrical equipment I - to be used - for gases it is specified as corresponding with one in mines where there's temperature class risk of mine gas explosion determining max several anti-explosion II - to be used surface temperature... -
Page 12: Data Plates
5.2. Data Plates Data plates of PM02.EX-1-* power supply: Data plates of PM02.EX-2-* power supply:... -
Page 13: Information Stickers Arrangement
EX mark: gases (read section 5.1). EX mark: dusts (read section 5.1). Electrical rating Warning about electrostatic charge danger (n/a for PM02.EX-2-* power supply) and against opening at voltage; in Polish, English, German, other . 5.3. Information Stickers Arrangement Fig.5. Arrangement of data plates and security stickers 1 - Cover's security seals. -
Page 14: Installation And Start-Up
Prior to installation and start-up, carefully read this user manual. Use the device only as intended. RADWAG does not bear any responsibility for damage or losses resulting either from improperly carried out installation or misuse. Prior to installation and start, it is necessary to analyse whether the device complies with the usage requirements regarding particular hazardous area. -
Page 15: Power Supply Grounding
The operator has no access to the internal components of the power supply. Due to the quantity of led intrinsically safe circuits and cable termination, there are two versions of the power supply: PM02.EX-*-1 and PM02.EX-*-2 6.4.1. PM02.EX-*-1 Power Supply V1, V2, V3, V4, V5 output circuits are led through the gland using cable. - Page 16 WIRE NUMBER SIGNAL Power supply board 486R Fig.7. Connection of intrinsically safe cable to PM02.EX-*-1 1 – Output voltages marking 2 – Cable wire number The user, on the pain of losing the intrinsic safety, is obliged to connect the cable of intrinsically safe output circuits to the junction box of his/her electrical system.
-
Page 17: Pm02.Ex-*-2 Power Supply
Power supply connection method differs depending on the installation option: PM02.EX-1-* – power supply – is equipped with power cord of 100 - 240VAC that is not terminated with a plug. Respectively prepared power cord's wire ends (stripped, tin-plated or terminated with tubular end... -
Page 18: Maintenance
PM02.EX-2-* – power supply – is equipped with power cord of 100–240VAC that is terminated with a plug featuring a ground pin, the plug type is conditioned by region/country. Connect the cable to the wall outlet with a ground pin. -
Page 19: Technical Condition Inspection
It is not allowed to clean the power supply using compressed air. 8. TECHNICAL CONDITION INSPECTION The technical condition of the PM02.EX-*-* power supply must be tested and inspected by a trained personnel (familiar with this user manual content) at least once every three months. -
Page 20: Recycling
10. RECYCLING PM02.EX-*-* power supplies must be recycled, they are not to be treated as a regular household waste. Platforms to be decommissioned must be decommissioned in accordance with valid legal regulations.