Related Manuals for AGT GS1500
Summary of Contents for AGT GS1500
- Page 1 Walk Behind Wood Chipper 15HP B&S Powered MODEL: AGT-GS1500 Please read the product manual completely before assembly Check against the parts list to make sure all parts are received Wear proper safety goggles or other protective gears while in assembly...
-
Page 2: Table Of Contents
Table of Contents PART I: General Safety Rules ..................03 PART II: Familiar with the Wood Chipper ................. 09 PART III: Install the Wood Chipper ..............10 PART IV: Operating the Wood Chipper ................. 15 PART V: Maintaining the Wood Chipper ................17 PART VI: Troubleshooting and Parts List ................ -
Page 3: Part I: General Safety Rules
PART I: General Safety Rules Safety Labels Found on Your Unit WWW.AGROTKINDUSTRIAL.COM P 3 / 2 3 T o l l F r e e : 913-244-6269... - Page 4 WARNING Read this Safety & Operating Instructions manual before you use the Wood Chipper. Become familiar with the operation and service recommendations to ensure the best performance of your machine. WWW.AGROTKINDUSTRIAL.COM P 4 / 2 3 T o l l F r e e : 913-244-6269...
- Page 5 Propose CAUTION This machine is designed solely to chip wood and must not be used for any other purpose. It should only be used by trained operators who are familiar with the content of this manual. It is potentially hazardous to fit or use any parts other than your dealer parts. The company disclaims all liability for the consequences of such use, which in addition voids the machine warranty.
- Page 6 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and themselves. Always wear protective goggles or safety glasses with side shields while using the Wood Chipper to protect your eyes from possible thrown debris. Avoid wearing loose clothing or jewelry, which can catch on moving parts.
- Page 7 heater, clothes dryer or furnace. Never make adjustments or repairs with the engine running. Shut down the engine, disconnect the spark plug wire, keeping it away from the spark plug to prevent accidental starting, wait 5 minutes before making adjustments or repairs. Never tamper with the engine’s governor setting.
- Page 8 Never operate the machine when under the influence of alcohol, drugs, or medication. Use the machine only in daylight. Stay alert for hidden hazards or traffic. Keep all nuts and bolts tight and keep the equipment in good operating condition. A Note to All Users List of warnings and cautions cannot be all-inclusive.
-
Page 9: Part Ii: Familiar With The Wood Chipper
PART II: Familiar with the Wood Chipper It may be helpful to familiarize yourself with the controls and features of the Wood Chipper. If you have any question, please contact the dealers in your area. TECHNICAL SPECIFICATIONS Start Recoil Start Engine 13.5HP four strokes Power... -
Page 10: Part Iii: Install The Wood Chipper
PART III: Install the Wood Chipper 1. After unpacking, check the following components Description Quantity Description Quantity Machine body assembly Tow bar Feet fixation In-feed assembly Standing leg Discharge chute assembly Tire Tool-wrench WWW.AGROTKINDUSTRIAL.COM P 10 / 2 3 T o l l F r e e : 913-244-6269... - Page 11 2. Installation in-feed assembly Parts no. Description Specifications Quantity Machine body assembly In-feed assembly Bolt M8x20 Washer Spring washer Feed to frame rubber 3. Installation tire system WWW.AGROTKINDUSTRIAL.COM P 11 / 2 3 T o l l F r e e : 913-244-6269...
- Page 12 Parts no. Description Specifications Quantity Machine body assembly Tire axis Tire Lock nut Slotted nut Bolt M10x25 Washer Washer Split pin Ø4x32 Rubber cover 4. Installation standing leg assembly Parts no. Description Specifications Quantity Machine body assembly Feet fixation Standing leg Lock nut Bolt M10x25...
- Page 13 5. Installation tow bar Parts no. Description Specifications Quantity Machine body assembly Tow bar Lock nut Bolt M10x65 Washer Spring washer 6. Installation discharge chute assembly Parts no. Description Specifications Quantity Machine body assembly Discharge chute assembly Bolt M10x30 Washer Spring washer Discharge to frame rubber WWW.AGROTKINDUSTRIAL.COM...
- Page 14 7. Connect electric wire Emergency Stop Switch Protection Switch Step. 1: Check the electric wire on the machine Step. 2: Find the A and B electric wire find the ①②③ contact join Step. 3:Contact ① and A electric wire Contact ② and B-1 electric wire Contact ③...
-
Page 15: Part Iv: Operating The Wood Chipper
PART IV: Operating the Wood Chipper It may be helpful to better familiarize yourself with the features of your Wood Chipper before beginning the steps outlined in this chapter. WARNING Read and understand all instructions, safety precautions, and/or warnings listed in “PART I: General Safety Rules”... - Page 16 Stopping Move the Throttle Lever to IDLE. Recoil Start: Turn the Ignition Switch to the OFF position. Electric Start: Turn the Key to the OFF position. Operator Zone Wood Chipping NOTICE Woods’ and branches’ diameter should be no bigger than 120mm. WARNING Do not place your hands into the chute when loading.
-
Page 17: Part V: Maintaining The Wood Chipper
PART V: Maintaining the Wood Chipper Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's user manual for maintenance procedures. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. - Page 18 Oil filter Replace the blade NOTICE The blade is a bidirectional blade. If one side of the blade is worn, the blade can be used after changing the direction without immediate replacement. Turn the roller axle with wrench Loosen the screws with T wrench when you see the blade Replace with a new blade After changing the blade, adjust the lower blade to keep the gap of 1-3mm WWW.AGROTKINDUSTRIAL.COM...
- Page 19 Adjust the clearance between blade and lower blade Loosen the NO.16 screw, then loosen the #27 screw, Move #59 on U-groove observe that the spacing between the roller blade and the lower blade spacer is within 1-3mm, Lock screw #27,Finally lock screw #16 Adjust blade clearance 1~3mm then...
-
Page 20: Part Vi: Troubleshooting And Parts List
PART VI: Troubleshooting and Parts List Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact the dealers in your area. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. - Page 21 WWW.AGROTKINDUSTRIAL.COM P 21 / 2 3 T o l l F r e e :913-244-6269...
- Page 22 PARTS LIST Ref.No. Description Ref.No. Description Foundation Big washer Tire axis Washer M8 Feet fixation Washer M12 Standing leg Washer M10 Tire 16*8-7 Washer M6 Tow bar Washer M30 Engine Spring washer M8 Belt cover Spring washer M12 Belt cover inner plate Spring washer M10 Chain Spring washer M6...
- Page 23 WWW.AGROTKINDUSTRIAL.COM P 23 / 2 3 T o l l F r e e :913-244-6269...