Advertisement
2.
INTRODUCTION & SPECIFICATION
Slim-line design suitable for floor or desktop operation - ideal when space is at a premium. Push-button heat controls with fan-only option.
Switched oscillating mode to improve hot or cold air distribution. Thermal and tip-over cut-out switches for improved safety.
Power: . . . . . . . . . . . . . . . . . . .1000/2000W
Supply: . . . . . . . . . . . . . . . . . . .230V – 13A
3.
ASSEMBLY
4.
OPERATION
WARNING! DO NOT operate the heater without the base attached. Do not operate the
o
heater lying on its side.
Place the fan in the area where it is to be used using the recessed carrying handle at the
3
back of the unit and plug it into the mains supply.
4.3
OPERATION
4.3.1 To operate simply push the power button down into the “ON” position and select the heat
setting you require.
4.3.2 There are three settings for the heater:
1) Cold air - both heat buttons in the OFF (UP) position
2) Warm air - first heat button depressed (I).
3) Hot air - both heat buttons depressed (I + II).
4.4
OSCILLATION
4.4.1 During use the heater can be made to turn from side to side. To commence oscillation
push the oscillation (OSCI) button down. To stop oscillation push the button again to
return to it to it’s “OFF” position (up).
5.
MAINTENANCE
5.1
REPAIRS
5.1.1 If any problems are experienced with the unit, take it to an authorised service centre for repair or maintenance. Do not attempt to
service the unit yourself. This can only be done by an authorised service agent.
5.2
CLEANING
5.2.1 If the unit requires external cleaning make sure it is switched off and unplugged from the mains supply. Use a soft tissue or cloth for
general cleaning. To remove more persistent dirt or grime, wipe down with a soft cloth and warm soapy water. Do not use solvents or
abrasive materials to clean the unit.
Declaration of Conformity
TOWER FAN HEATER
Model: STH2000
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12 months from
purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on
01284 757525 and leave your full name and address, including postcode.
01284 757500
fig 1
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 703534
Dimensions: . . . . . . . . .600 x 230 x 230mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . .3.4kg
Your Tower Fan heater is supplied fully assembled with the exception of the
o
base which comes in two halves. Please follow the assembly instructions
carefully.
3.1
ASSEMBLY
3.1.1 Feed the mains cable through the large section of the base and slot the
smaller section on, via the clips located on the adjoining edges (fig 1).
3.1.2 Secure the heater assembly to the base by means of the screws supplied,
the screw holes are located on the underside of the base.
3.1.3 Secure the loose cable into the cable clamp located at the rear of the
underside of the base.
www.sealey.co.uk
Web
fig 2
For Jack Sealey Ltd.
Sole importer into the UK
14th June 2005
of Sealey Power Products.
sales@sealey.co.uk
email
STH2000 - 1 - 140605
Advertisement
