Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ABSTRACTA Manuals
  4. Office Equipment
  5. Plenty Pod Medium
  6. Installation instructions manual

ABSTRACTA Plenty Pod Medium Installation Instructions Manual

Hide thumbs Also See for Plenty Pod Medium:

Advertisement

Quick Links

Download this manual
Plenty Pod
Assembly Instruction

Advertisement

loading
Need help?

Need help?

Do you have a question about the Plenty Pod Medium and is the answer not in the manual?

Questions and answers

Related Manuals for ABSTRACTA Plenty Pod Medium

Summary of Contents for ABSTRACTA Plenty Pod Medium

  • Page 1 Plenty Pod Assembly Instruction...
  • Page 2 Including the following screws and fasteners for Plenty Pod Medium Art.nr Pcs Description 575 046 04 4,2 x 25 screw with drill bit 575 045 04 4,2 x 14 screw with drill bit 377 001 01 UP-bracket (pairs, right-left) 54342146...

  • Page 3: Required Tools

    Required tools Spirit-level Screwdriver Ratchet Bit set, Ph, Torx, Insex Rubber hammer...
  • Page 4 Mounting Start with evening out the floor module which you want to set up your pod on. (An uneven floor can especially complicate mounting the glaswalls and fitting in the door)
  • Page 5 Do not screw the Plenty Pod into the floor if it contains floor heating, electric cables, water pipes or the like. Plenty Pod stands stable without fixing. If you need to attach Plenty Pod to the floor, use the appropriate screw and plug. Not included. Place the U-rails according to picture below Connect the U-rails and corners with U-rail connector.
  • Page 6 U-rail connector Place the distance plate according to picture.
  • Page 8 Distance Plate...
  • Page 9 Place the premounted wall module with the first Continue with the first set of separate bottom frame profiles as follows:...
  • Page 10 Loosen the set screw in the frame profile (Fig A) until the hammerhead bolt (Fig B) at the end of the profile can be turned and fit into the middle track of the vertical profile (Fig C). When the hammerhead bolt is inserted into the track, place the profile on the floor (Fig D).
  • Page 11 Alternatingly mount the separate vertical and horizontal profiles onto each other until the whole rail is filled.
  • Page 12 From the top, place the threshold between the vertical profiles, by sliding the attached L-bracket into the tracks. Drag it down to the floor. Squeeze the vertical profiles together so that there is no gap between them and the threshold.
  • Page 13 Fixate the L-profile in the vertical profiles. Mount the top horizontal profiles between the vertical profiles.
  • Page 14 Placement of profiles Seperate vertical Central pillar profils Socket Threshold Right top and bottom Left top and bottom horizontal profile horizontal profile Front horizontal Central pillar profile...
  • Page 15 Fabric wall mounting Find out which walls are going to have fabric, respectively glasses. For fabric walls, mount the vertical and horizontal L-profile profiles as shown below. L-profile 2 pcs 2038 mm 2 pcs 970 mm L-profile is mounted with screw (575 045 04, 4,2x14).
  • Page 16 Mount the UP-brackets (377 001 01).
  • Page 17 Place the acoustic walls inside, behind the L-profiles.
  • Page 18 Outside wall panels Begin at the top by hooking the track of the L-profile onto the UP bracket (377 001 01). The lower part of the wall panel should hang loosely. 377 001 01 Push the wall panel to the frame without connecting it to the bottom.
  • Page 19 Press straight from below on the wall panel, right up. Push the wall panel against the frame and let it fall down and connect to UP brackets. Press down the panel. Make sure it is hooked into all 6 UP brackets.
  • Page 20 Mounting glass walls Find out which walls are going to have fabric or glasses. Start by tucking the inside vertical glass wall profiles into the vertical frame profiles. (Fig A). Then take the inside horizontal glass profiles into the horizontal frame profile (Fig B). The rubber seal should be placed in the center of the profile (Fig B), where the glass shuold be placed.
  • Page 21 Carefully place the glass in the frame against the rubber seal. Mount the outer vertical glass wall profile to the frame. Then mount the outer horizontal glass wall profiles. Check that every profile is inserted correctly.
  • Page 22 Door mounting Screw the door frame to the vertical frame profile.
  • Page 23 Then place the top door frame and fixate with screws. Hang the door...
  • Page 24 Cover the holes with the plastic caps.

  • Page 25: Roof Mounting

    Roof mounting Mount the roof L-profile to the horizontal top frame profiles with screws (575 045 04).
  • Page 26 2075mm 1010mm 1010mm 2075mm...
  • Page 27 Insert the ceiling...
  • Page 28 Place the insulation Mount the top plate. Fixate with screw 4,2x25 (575 046 04)
  • Page 29 Done! Further questions? Contact our customer support advisers at Abstracta! +46 472 26 96 00...