Summary of Contents for aquabrass Aquasteam N2787
- Page 1 Aquasteam N2787/N2789/N2782 steambath generator 7.5KW 9KW 12KW générateur de vapeur 7.5KW 9KW 12KW last revision: 10/20/2016 aquabrass.com...
-
Page 2: Table Of Contents
Steambath Generator Systems INSTALLATION, OPERATION & MAINTENANCE MANUAL Table of Contents Read Me First! & Warning Placard ........1 Select Your Model ........2 Specification Chart .............2 Before Installing ..............3 Steam Room Guidelines.............3 Locating the Steam Generator Unit ........4 Typical Installation ..............4 Installation: Plumbing, Water Supply, Drain, Steam Outlet Safety Valve, Drip Pan, AromaSteam .... - Page 3 When installing and using this electrical equipment, basic safety precautions R E A D M E F I R S T ! should always be followed, including the following: IMPORTANT SAFETY INSTRUCTIONS IMPORTANT NOTE: As you follow these instructions, you will notice warning and caution symbols.
-
Page 4: Select Your Model
_________________________________________________________________________________________ Select Your Model WARNING In considering a purchase of this steam- Materials of construction, room size and special design features such as bath system, please note that if users are pregnant, large glass areas, all affect the steam generator model selection. have a coronary condition, are in poor health, are being treated for any other medical condition, or are using 1. -
Page 5: Before Installing
Before Installing the steambath room. Pay particular attention to room Carefully inspect the CT steam generator and packaging for volume and construction. shipping damage. In the event of shipping damage, please Marble or glass walls or ceilings “enlarge” the room’ s size contact the carrier for claim information. -
Page 6: Locating The Steam Generator Unit
Locating the Steam Generator Unit IMPORTANT NOTE: The control cables should be run in dedicated 1" conduit to facilitate installation and service Select a location as near as practical to the steam room. Typical locations include: closet, vanity cabinet, heated attic or basement. The maximum length of the N2762 is 60 feet. - Page 7 _________________________________________________________________________________________ TYPICAL INSTALLATION INSTRUCTIONS Printed Circuit Board Component shown enlarged for illustrative purpose. 1. Install each steam generator as in a single installation. Install genera- tors as close as practical to each other, not exceeding 10 feet. The interconnecting cable length is 12 feet. WARNING Shock Hazard.
-
Page 8: Water Quality Information
_________________________________________________________________________________________ Installation WARNING To insure proper and automatic safety valve Plumbing operation: DO NOT connect a shut off valve or a plug at All plumbing shall be performed by a qualified licensed plumber safety valve outlet. DO NOT connect a shut off valve or any and in accordance with applicable National and local codes. - Page 9 Installing the AromaSteam Steamhead ⁄ " NPT) 1/8" minimum clearance Use Teflon ® required for Acrylic Shield. equal sealant on ⁄ NOTE: A 1 " clearance hole around the steam pipe is pipe threads needed to mount the steamhead. STEP 1 Steam Locate steam head 6-12 inches above floor, except for: Supply Pipe...
-
Page 10: Generator Dimensions
_________________________________________________________________________________________ Generator Dimensions Water Inlet Steam Outlet Safety Valve AutoFlush Manual Drain Valve 12” (305) for servicing 17" " " (432) (162) (60) " (45) " (466) Water Inlet Control & Accessory " Connections (310) Steam Outlet Safety Valve " (251) "... - Page 11 _________________________________________________________________________________________ Electrical All electrical wiring to be installed by a qualified licensed elec- trician in accordance with National Electrical Code and local electrical code. Power Wiring- See “Field Power Wiring” Diagrams (below) ______________________________________________________________ Amper e Chart ____________________________________________________________ Maximum Room Voltage/ Wire Size Model No.
-
Page 12: Wiring Diagrams
_________________________________________________________________________________________ Single Phase POWER INPUT Wiring Diagrams Transformer L E G E N D (All Diagrams) FIELD WIRING FACTORY WIRING Express Steam WATER MODEL FEED SOLENOID GROUND VALVE THERMOSTAT CONTACTOR AutoFlush HEATER MSTS CT-SteamStop TEMP. PROBE HEATING ELEMENT To Probe Control THERMOSTAT POWER INPUT... -
Page 13: Initial Start-Up & Checkout
_________________________________________________________________________________________ Maintenance Initial Start-Up and Checkout steambathgenerators require little maintenance. Turn on control. Follow specific instructions provided with controls. Other than draining, maintenance procedures are minimal. When Steam will beginto appear in approximately min- AutoFlush is not installed the manual drain valve should beopened utes at the steam head. - Page 14 _________________________________________________________________________________________ System Status Codes control may display a status code if the steam generator is not functioning properly. Code Code Meaning Probable Cause Suggested Remedy Water level is not Water Supply is off Turn on Water Supply satisfied within 5 min. Defective water feed solenoid Check/replace water solenoid valve Water feed probe not functioning...
- Page 15 TROUBLESHOOTING WARNING All electrical troubleshooting to be performed by a qualified licensed electrician Step 1 Check main incoming power to the unit. Step 2 Ensure the black wires from the pri- mary side of the transformer are connected Contactor to the quick connect tabs on the line side Water Feed Solenoid of the contactor.
-
Page 16: Autoflush ® System
_________________________________________________________________________________________ ® AutoFlush 3 Pin Connector Box Contents for AutoFlush • AutoFlush Valve with Cord • Installation instructions. Operation The AutoFlush System feature automatically drains the system following each use. AutoFlush Cord Connector A time delay allows the water to cool down (about two hours) before it drains by gravity for a safe and gentle operation. -
Page 17: Replacement Parts List
_________________________________________________________________________________________ Replacement Parts List ____________________________________________________________ Part No. Description Product ____________________________________________________________ 99178CT Drain Valve All models 99297 Safety Valve 15PSI All models 100479 Water Feed Solenoid All models Valve w/filter 10477-3 Transformer 24VAC All models 103975 Liquid Level Control Board All models 100476-2 Contactor 50A 2-pole Single phase... - Page 18 _________________________________________________________________________________________ Contactor Liquid Level Control Board shown with cover removed Transformer Water Feed Liquid Level Probe Solenoid Power Supply Knock-Out Water Inlet Plug and Play Connection (see page 13) Steam Outlet Access Cover Safety Valve NOTE: FOR ILLUSTRATIVE PURPOSES ONLY. Some components may be AutoFlush Valve...
- Page 19 _________________________________________________________________________________________ Care Tips for all Controls and Steamheads 1. Use only mild soap and water on a soft cloth to clean the control and steamhead. 2. Do not use abrasive cleansers. 3. If the decorative cover is damaged on the iTempo/ Plus call Mr.Steam technical service for replacement parts.
- Page 20 Care Entretien To clean your Aquabrass faucet or accessory, wash with a wet nonabrasive soapy cloth. Then wipe dry with a soft towel or cloth. We recommend this be done on a regular basis. DO NOT USE ANY ABRASIVE, CHEMICAL OR CORROSIVE, POWDER OR ANY OTHER STRONG CLEANERS INCLUDING DETERGENTS, WINDOW CLEANERS AND DISINFECTANTS ON YOUR Aquabrass PRODUCT as they will destroy the finish and therefore VOID THE WARRANTY.
- Page 21 - Aquabrass polished chrome and brushed nickel finishes are warranted for the life of the product to the original purchaser. All other finishes will be war- ranted for five years (Satin Nickel Natural [#210] is designed to develop a patina over time). Raw Brass (#400) is a living finish for which there is no warranty Normal wear and tear is not covered by this warranty.
Need help?
Do you have a question about the Aquasteam N2787 and is the answer not in the manual?
Questions and answers