Crivit 14145 - LED Bike Light Set Manual

List of pictograms used

	Read the instructions!		USB – Universal Serial Bus – Connection port, e.g. on a computer (charging only).
	Danger to life and risk of accident for infants and children!	K XXXXX	German Federal Motor Transport Authority test symbol (K followed by approval number).
	Observe the warnings and safety notices!		Product and packaging should be disposed in an environmentally friendly manner.
	Caution! Explosion hazard!		Recycling code for cardboard disposal.
	Symbol identifying electrical and electronic devices.		Product meets the applicable European product-specific directives
	Improper disposal of rechargeable batteries may result in environmental damage!		Recycling code for the disposal of polyester fibres and films.

Introduction

Congratulations on the purchase of your new product. In doing so you have chosen a top-quality product. The instructions for use are to be considered as part of this product. It contains important safety, assembly and disposal information. Before using the product, please familiarise yourself with all the safety information and instructions for use. The product must only be used as described and for the specified fields of application. If you pass the product on to anyone else, please be sure to also include all documentation.

Intended use

This product is suitable for lighting the roadway whilst cycling. The LED Bicycle Light Set is approved as exclusive lighting for all bicycles. Light distribution must not be impaired by other bicycle parts or luggage. The product is intended for outdoor use. Any use other than the aforementioned or any product modification is prohibited and can result in injuries and product damage. The manufacturer is not liable for damages resulting from improper use. This product is not intended for commercial use.

Parts description

1. Headlight bracket
2. Headlight sensor
3. Headlight sensor control light
4. Headlight on / off switch
5. Headlight battery control system
6. Headlight
7. Rubber tab for headlight bracket
8. Headlight lock
9. Tail light bracket
10. Tail light lock
11. Tail light bracket rubber tab
12. Tail light on / off switch
13. Tail light rechargeable battery control system
14. Tail light
15. Star screw tail light bracket
16. USB cable
17. Rechargeable battery charging socket (Headlight and tail light)

Scope of delivery

1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
1 USB cable
1 Instructions for assembly and use

Technical data

Headlight (auto-dimming)

Model designation: LI-3A / XC-266
Rated output: 2 W
Protection type:

IP44 according to
DIN EN 60529 Rechargeable

Rechargeable Li-ion battery: 1300 mAh, 3.7 V

Tail light

Model designation: LR-2 / XC-249
Rated output: 0.2 W
Protection type:

IP44 according to
DIN EN 60529 Rechargeable

Rechargeable Li-ion battery: 300 mAh, 3.7 V

Safety instructions

• 
  DANGER TO LIFE AND RISK OF ACCIDENT FOR INFANTS AND CHILDREN! Never leave children unsupervised with the packing material due to the suffocation hazard posed by swallowing parts thereof. Children frequently underestimate the dangers.
• Always keep the product away from children. This product is not a toy!
• This product may be used by children 8 years and up as well as by persons with physical, sensory or mental impairments or lacking experience and knowledge, when supervised or instructed in the safe use of the product and understand the associated risks. Do not allow children to play with the product. Cleaning and user maintenance must not be performed by children without supervision. Please note, damages caused by incorrect handling, non- compliance with the operating instructions or interference with the device by unauthorised individuals are excluded.
• Never take the product apart. Improper repairs can put the user in considerable danger.
  Repairs should only be carried out by specialist personnel. The LED lights are not replaceable.
  The LED lights cannot be replaced.

RISK OF LOSS OF LIFE AND ACCIDENT! Using the incorrect charger may cause the headlight and the tail light to be damaged, overheat or even explode. Doing so will void the warranty.

Safety instructions for rechargeable batteries

• 
  EXPLOSION HAZARD! Keep rechargeable batteries away from children, do not throw rechargeable batteries into fire, do not short-circuit and do not take apart.
• Failure to observe this instruction may result in the rechargeable batteries discharging beyond their end voltage. This poses a risk of leaking.
• Avoid contact with the skin, eyes and mucous membranes if fluid has leaked from the rechargeable batteries. In the event of contact with battery acid, thoroughly flush the affected area with clean water and seek immediate medical attention.
• Note: If the red LED on the battery control system lights up on the headlight or the tail light , please recharge the batteries immediately.
• After the battery control system lights up on the headlight and the tail light, these will continue to give out light for at least 30 minutes.

Installation

Installing the headlight

(see Fig. A)

• Position the bracket at the desired point on the handlebars.
• Secure the bracket in place on the handlebars using the rubber tab . When doing so, ensure that there are no objects in front of the headlight .
• Apply tension to the rubber tab and hook it in. To prevent damage, do not use tools for this step.
• To adjust the optimum angle to the direction of travel, turn the headlight into the correct position (see Fig. A)
• Slide the headlight into the bracket , until you hear it lock into place.
• To release, press the headlight lock and slide the headlight forward out of the bracket .

ATTENTION
Routinely verify the headlamp adjustment. The light cone must point straight ahead, in the direction of travel, and must not be adjusted too high so as not to blind oncoming traffic.

Installing the tail light

(see Fig. C)

• Secure the bracket in place on the seatpost or the rear seat stays using the rubber tab. Be sure there are no objects in front of the tail light .
• Tighten and hook in the rubber tab .
• Loosen the star screw on the bracket and adjust to the desired angle.
• Then tighten the screw. Tighten the screw hand tight. To prevent damage, do not use tools for this step.
• Slide the tail light into the bracket until you hear it lock into place. Ensure that the tail light is assembled as depicted in Fig. C.
• To remove the tail light press the tail light locking mechanism and take off the tail light .

ATTENTION
The tail lamp must be installed and adjusted so the reference axis is parallel to the median longitudinal plane of the vehicle and parallel to the road.

Operation

Switching on/off

The headlight has three brightness settings.

On/Off switch
press once	Auto-mode: The headlight is equipped with a sensor which automatically regulates the brightness of the headlight depending on the environmental conditions. When the sensor is active (auto-mode), the sensor control light flashes green.
press twice	Power mode (60 Lux) for riding in unlit areas
press three times	Standard mode (30 Lux) for riding in lit areas
press four times	Eco mode (15 Lux) for riding in well lit areas
press five times	power off
Battery
Battery charge status		Operating mode of the battery control system:
100% - 75%		4 green LEDs light up
75% - 50%		3 green LEDs light up
50% - 25%		2 green LEDs light up
25% - 10%		1 green LED lights up
10% - 0%		1 red LED flashes

Tail light

Charging the headlight / tail light

(see Fig. D+E)

• Remove the rubber cover from the battery charging socket and connect the USB cable to the battery charging socket .
• Then connect the USB plug of the USB cable to a computer / laptop / standard USB charger with 5 V DC and 500 – 1000 mA. The use of chargers with different specifications can damage the bat teries, and in turn the headlight and tail light. Doing so will void the warranty.
• Headlight and tail light both have a battery control system. The battery control system on the headlight flashes red when the batteries are empty and must be recharged. The battery control system on the tail light lights up red when the batteries are empty and must be recharged. During charging, the battery control system lights up green. When the batteries are ready to be used again, the battery control system will go off and you can use the headlight and tail light .
• For the built-in rechargeable battery to operate at full power, please do not charge the headlight re chargeable battery for less than 6 hours the first time (tail light: no less than 5 hours). Please do not stop charging sooner, even if the LED is already extinguished. After this, a charging time of approx. 3.5 hours is recommended for the headlight (recommended charging time for the tail light is 2.5 hours).

Cleaning and care

• Never fully immerse the headlight and tail light in water. Do not use corrosive or abrasive cleaning agents. Doing so will damage the lights.
• Use a dry, lint-free cloth when you clean or maintain the product.

Diekbree 8, DE-48157 Münster, DEUTSCHLAND
Tel: +49 2 51 132 37 57
E-Mail: de@klb-service.eu www.klb-service.eu

Documents / Resources

References

• KLB-Information

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Crivit 14145 - LED Bike Light Set Manual