Summary of Contents for Racer RACCOMBID314T
- Page 1 ORIGINAL INSTRUCTIONS >EN GASOLINE MULTI TOOL KIT RACCOMBID314T INSTRUCTION MANUAL CAUTION: Read the instructions before using the machine!
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTIONS ....................3 YOUR PRODUCT ......................14 ASSEMBLY ........................17 FILLING OIL TANK AND FUEL TANK ................22 OPERATION ........................24 MAINTENANCE AND STORAGE ..................28 DECLARATION OF CONFORMITY ................. 29 WARRANTY ........................30 PRODUCT FAILURE ......................31 10. -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS Safety instructions for brushcutter and grass trimmer Proper safety precautions must be observed. This unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read and understand the machine manual and are trained in its operation. - Page 4 of any other accessories or attachments may cause injuries to the user, damage to the machine and void this warranty. When refuelling, be sure to stop the engine and confirm that it is cooled down. Never refuel when the engine is running or hot.
- Page 5 Clean and maintain the tool before storage (see the chapters on this manual). Bring maintenance after each use according the instructions of this manual. Improper maintenance can reduce the lie of the tool, bring bad results and wear the tool and its accessories. ...
- Page 6 Contact with projected objects Burns when touching with hot surfaces Prolonged use of this product exposes the operator to vibration and can produce so-called "white finger" disease. To reduce the risk, wear gloves and keep your hands warm. If any of the symptoms of "white finger syndrome" occur, seek immediate medical attention. Symptoms of the "white finger"...
- Page 7 plug and take the following steps: inspect for damage; check for, and tighten, any loose parts; have any damaged parts replaced or repaired with parts having equivalent specifications h) Wear ear protection. Wear eye protection. In case of emergency, stop the hedge trimmer; release the trigger, switch off the tool with the ON/OFF button.
- Page 8 When a danger or a non-intended situation arise, stop to work immediately and switch off the tool. Restart to work when there is no danger and you can work safely. Cut before the large branches with a hand shears to avoid the blocking of the blade. ...
- Page 9 Safety warnings for the mounted pole pruner Proper safety precautions must be observed. This unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read and understand the machine manual and are trained in its operation.
- Page 10 engine is running or hot. When gasoline spills, be sure to wipe it up completely dispose of those materials before starting the engine. Stay clear of other workers or bystanders by at least 15 meters. Whenever approaching an operator of the machine, carefully call his attention and confirm that the operator stops the engine.
- Page 11 Check the tool before and after use. Check for loose fasteners, fuel leaks and damaged parts, such as cracks in the cutting attachment. If the tool is damaged, if parts are missed or meet some dysfunctions, do not use the tool and bring it to a service agent for inspection and reparation. ...
- Page 12 condition. These symptoms usually appear on the fingers, hands or wrists. Risk increases at low temperatures Inhalation of particles Inhalation of exhaust gases Unattended projections Contact with foreign objects Contact with the tool in operation Hearing loss in the absence of correct hearing protection To minimize those risks, follow the instructions of this manual about wearing personal equipment of protection, take some rest during the operation and the manipulation of the tool.
- Page 13 Wear protective footwear Caution to exhaust gases Do not smoke and do use the tool near naked flame The accessible part are hot when operate the tool Caution! Risk of rebound Keep bystanders away at least 15m Warning – Risk of electric shock. Always beware of the danger from overhead electric- power line, keep a safe distance at least 10m from the power line Caution! The tool can contact to a voluminous material.
-
Page 14: Your Product
2. YOUR PRODUCT a. Description... - Page 15 1. Unit 9. Carter of protection 2. Handle 10. Flexible tube 3. Cutting attachment installation 11. Blade for brush cutter 4. Tube 12. Air filter 5. Command cord 13. Choke lever 6. Accelerator throttle 14. Starter rope 7. ON/OFF switch 15.
- Page 16 b. Technical data Engine displacement 31cm³ Brush cutter: 9300min-¹ Maximum engine speed Grass trimmer: 8000min-¹ Maximum power 0,7kW Mass 17.5kg Volume of fuel tank 0.7 L Volume of oil tank 0.08L Grass trimmer: 480mm Cutting diameter Brushcutter: 255mm Brushcutter: 1,4mm (metal blade) Cutting thickness Grass trimmer: 2,4mm (non-metallic flexible line) Brushcutter: single piece (three teeth metal)
-
Page 17: Assembly
3. ASSEMBLY Assembling the flexible tube with the engine and the pipe support Pull the key which is on the clutch housing. Insert end of the flexible tube (with the hole) into the clutch housing on the engine until it locks in place. Release the key. Insert the other end of the flexible tube into tube until it locks into place. - Page 18 Handle Install the front handle as shown in the image. Do not fix the screws until you have set the most comfortable working position. Tube Install the desired tube on the bar of the main unit. Make sure the locking pin is inserted into the hole in the bar.
- Page 19 Installation of the 3-tooth metal blade (for brushcutter operation) Warning - sharp edges; wear gloves when manipulate the blade. Insert a metal locking tool in the hole on the side of the drive sprocket and on the drive. Remove the retaining nut, the cover bell and the plate. Install in the following order, on the shaft: the blade, the plate, the cover bell and the retaining nut.
- Page 20 Adjusting of the position 1. Press the release / safety plate to loosen and turn the unit to the desired position depending on the nature of the work to be performed. 2. Loosen the release / safety plate ensuring that the cutting accessories are securely in place and secured. Pruner Tighten the tightening wheel Release the cutting blade to the machine tube (Make sure that the lock is engaged in the fixing hole.
- Page 21 Adjusting the chain tension The chain must not have too much clearance, but it must be possible to lift the chain a few millimetres from the guide rail. Loosen the fixing screw Raise the end of the chain guide slightly Check the ease of operation of the cutting chain by turning it manually.
-
Page 22: Filling Oil Tank And Fuel Tank
4. FILLING OIL TANK AND FUEL TANK a) Fuel Warning: Gasoline is highly flammable. Keep the fuel in specially designed cans. Only fill the tank outside and do not smoke during the operation. Avoid sparks or open flames near the fuel. Fill the tank before starting the engine. - Page 23 b) Oil - Open the oil tank. - By using the provided container, pour the oil in the tank. Do not overfill. - Close the tank. Wipe off all overfill oil. Information Recommended oil: We recommend the use of high-quality detergent oil classified for SF, SG, SH, SJ or higher.
-
Page 24: Operation
5. OPERATION Cold starting Put the tool on a plane surface. Push the ON/OFF switch on the ON position. Close the choke lever. Push the priming bulb 7 to 10 times. Pull the starter rope several times when the engine boom. Open the choke lever. - Page 25 Hot starting Open the choke lever or put it in the middle. Pull the starter rope. Press and hold the safety switch and then accelerator throttle to start the operation Stopping Release the accelerator throttle. Push the ON/OFF switch on the OFF position. Let the tool completely stop...
- Page 26 a) Grass trimmer operation - Trimming Tilt the head slowly to direct debris away from you. If cutting up to a barrier such as fence, wall or tree, approach from an angle where any debris ricocheting off the barrier will fly away from you, Move the line head slowly until the grass is cut right up the barrier, but do not jam (overfeed) the line into the barrier.
- Page 27 Scything weeds This is cutting by swinging the blade in a level arc. It can quickly clear areas of field grass and weeds. Scything should not be used to cut large, tough weeds or woody growths. Scything can be done in both directions, and just in one way which results in the debris being thrown away from you.
-
Page 28: Maintenance And Storage
6. MAINTENANCE AND STORAGE After each use, bring cleaning and maintenance to the tool; check for loose fasteners, fuel leaks and damaged parts, such as cracks in the cutting attachments. Keep the machine in good working condition. a) Air filter Accumulated dust in the air filter will reduce engine efficiency. -
Page 29: Declaration Of Conformity
Tel: +33 (0)5.34.502.502 Fax: +33 (0)5.34.502.503 Declares that the machine: GASOLINE MULTI TOOL KIT 52CM³ RACCOMBID314T Serial No: 20211189434-20211189743 Have been designed in compliance with the following standards: EN ISO 11680-1:2011; EN ISO 11680-2:2011; EN ISO 11806-1:2011; EN ISO 11806-2:2011 EN ISO 10517-1:2019;... -
Page 30: Warranty
8. WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 31: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: • Empty the fuel tank. • Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 32: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •... - Page 33 BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux – France Made in PRC 2021...