Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SPAN F450T
- Page 1 OWNER’S MANUAL Model: F450T STANDING TRANSFER AID Ensure the product has been assembled according to the instructions in this manual. All operators should read and understand the instructions for safe and proper operation of the patient lift.
-
Page 2: Definitions & Symbols
Refuse delivery if the packaging appears to be badly damaged. If the merchandise is damaged or any component is missing, contact the shipping company immediately and fi le a claim. For further assistance, contact your local dealer or Span-America. DEFINITIONS & SYMBOLS n this manual the user refers to the patient or resident and may be used interchangeably at diff... -
Page 3: Safety Instructions
Safety Instructions • FAILURE to use this device according to instructions may cause serious injury. • NEVER attempt to transfer a patient or resident whose weight exceeds the indicated maximum capacity for this device or any accessory. • NEVER leave a patient unattended during transfer •... -
Page 4: Product Features
Adequate arm strength is required if the patient must use present a potential for falling down will find the F450T a useful and safe transfer device. For patients who lack these requirements, a sit-to-stand lift such as the electric powered Span patient lift is preferred and recommended. -
Page 5: Specifications And Options
Specifications & Options SPAN F450T Maximum Capacity 450 Lb / 205 Kg Minimum Base Width 26.8 Maximum Base Width 37”* Open Base Width 37”* Closed Base Width 26.7” Base opens Overall Height 43.3” Base Height 4.5” Minimum Seat Height 26.7”** Seat Width 20”... - Page 6 Assembly Prior to assembly, unpack all parts from the shipping carton and check for any missing parts. Contact your dealer immediately if a part is missing. Parts List Cross Bar x 2 Right Side Arm Left Side Arm Side Support Arm x 2 Knee Pad Support Bar Knee Pad x 2 Seat x 2...
- Page 7 Step by Step Assembly Place the base assembly on the ease of assembly. Insert the kneepads into the support bar and secure them in place with bolts and washers (A2 + A5 + A4) as indicated below. Cover the two bolt heads with black plastic caps (A7) to complete kneepad assembly.
- Page 8 Line up the small holes on the underside of the tubes with the Insert the two cross bars into holes in the support units. the holes on the seat and handle bar support units. Use the 4 hex screws (A3) with Allen key (T2) to tighten the completed assembly Insert the kneepad side support assembly...
- Page 9 Use the remaining 4 carriage bolt assemblies to securely fasten the two sub assemblies to the base unit. All of the square shoulders of the bolts should be on the inside and the washers and lock nuts on the outside. (A1 + A4 +A5 +A6)
- Page 10 Raise the two split seat units up and parallel to the side of the STEP 1 Span F450T as shown below. Have the patient positioned at the edge of the surface and STEP 2...
- Page 11 Lock the casters by stepping on the caster clip and STEP 3 pushing down as shown below. Have the patient grasp the cross bar closest to them and STEP 4 using their own strength pull themselves up into a standing as shown.
- Page 12 Have the patient lower themselves down onto the seat while keeping their STEP 6 knees/shins in the knee/shin pads and while still holding the cross bar with both hands as shown. Unlock the casters and place both hands on the cross bar furthest from the patient and move the standing transfer aid STEP 7 to the new surface.
-
Page 13: Maintenance And Inspection
Maintenance & Inspection • The Span F450T Standing Transfer Aid is a manual unit and therefore requires minimal maintenance on an ongoing basis. However to insure safety and proper use the following steps should be taken on a monthly basis. - Page 14 Accessories The F450T Standing Transfer Aid is designed to fully support a seated patient for transport. For patients requiring some upper body support or additional security a safety belt may be used. Either the SL-SA669 Standard or SL-SA669B Extra Large slings are designed to work with the F450T.
- Page 15 RETURN GOODS POLICY Patient lifts may not be returned unless the wrong lift is shipped in error by Span or the lift is heavily damaged or defective out of the box. For all other items, purchaser may request a RA for purchased goods within thirty (30) days of purchase invoice date.
Need help?
Do you have a question about the F450T and is the answer not in the manual?
Questions and answers