Summary of Contents for Onlyfire F-BRK6084
- Page 1 WOOD PELLET GRILLS F-BRK6084 OWNER’S MANUAL MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS EMAIL: .com WEBSITE: VN052021...
-
Page 3: Table Of Contents
CONTENTS IMPORTANT SAFETY INFO COMPONENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Z GRILLS SUPPORT 3-Y LIMITED WARRANTY... - Page 4 SAVE THIS MANUAL FOR FUTURE REFERENCE...
-
Page 5: Important Safety Info
IMPORTANT SAFETY INFO GENERAL WARNINGS Please read this entire manual before installation and use of the pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. - Page 6 similar liquids to start or ‘freshen up’ a fire in this appliance. Keep all such liquids well away from the appliance when in use. Do not use accessories not specified for use with this appliance. NOTE: A MAJOR CAUSE OF FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS.
- Page 7 This grill is designed for use of wood pellets only designed for burning in wood pellet grills. Do Not Use Pellet Fuel Labeled As Having Additives. We suggest that you use Z GRILLS BBQ WOOD PELLETS, which are specifically made to work in our grills. There is no guarantee that other brands of pellets are suitable for use in Z GRILLS.
-
Page 8: Component List
COMPONENT LIST... - Page 9 HARDWARE PACKAGE LIST...
-
Page 10: Assembly Instructions
ASSEMBLY INSTRUCTIONS PARTS DIAGRAM... - Page 11 HOPPER BURNER ASSEMBLY 1.BODY FRAME ASSEMBLY Turn the body upside down. Attach four legs (33) to the Grill Chamber Assembly by using Bolt (A). Use Allen Wrench (C) to tighten.
- Page 12 2.INSTALLING CHAMBER HANDLE TO LID 1. With the Lid (1) open, Use Allen Wrench (C) to tighten Bolts (A). Be careful not to over tighten. 3. 组装挡雨板 将挡雨板用ST4.0*10(B)螺钉用螺丝钉(D),固定在上盖上面.
- Page 13 4.POSITIONING THE GREASE DRAIN PAN Place the Grease Drain Pan (43/44) into the grill chamber assembly, as shown. 5.ATTACHING COOKING GRATE Attaching the Porcelain Cooking Grate (5) in the chamber.
- Page 14 6. ATTACHING WARMING RACK Attaching the Porcelain Warming Rack (4) in the Cooking Grate. 7. HANG ON THE GREASE BUCKET Hang the Grease Bucket (42) on the Bolt, as shown.
- Page 15 8. 组装电源线 将电源线 (36) 插到品字电源线座上.
-
Page 16: Initial Firing Instructions
INITIAL FIRING INSTRUCTIONS Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Warming Rack and Grease Drain Pan from the interior of the grill. -
Page 17: Subsequent Start-Up
SUBSEQUENT START-UP ATTENTION: If the grill fails to light or the fire in the Firepot goes out while cooking, it is vital to follow these steps when sufficient pellets are still in the Pellet Hopper. Failure to follow the steps may cause a hazardous “over-firing” of your grill due to an excess of unburned pellets in the Firepot. -
Page 18: Operating Tips
OPERATING TIPS 1.Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open. -
Page 19: Maintenance & Cleaning
MAINTENANCE & CLEANING Your Z GRILL requires regular maintenance. Make sure your grill is OFF, unplugged and completely cold before performing any maintenance and cleaning. Grease 1.With regular use your grill will accumulate grease on the Flue Lining, the Grease Drain Tube, the V-shaped Grease Drain and the Grease Drain Pan. - Page 20 Clean the ash from the interior of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF, UNPLUGGED AND COLD BEFORE ATTEMPTING TO CLEAN ASH FROM THE GRILL.
-
Page 21: Troubleshooting
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Potential Problem Solution Cause Make sure the power cord is plugged Power in. Verify there is power at the electrical outlet. - Page 22 Grill temperature is influenced by environmental factors such as high temperature, wind and direct sun. Unexpected grill temperature is External Factor Place unit in shaded area. Open the lid displayed to reduce inside temperature. After start your grill in 40 minutes, the grill will reach your desired temperature.
-
Page 23: Digital Thermostat Control Wiring Diagram
DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM... -
Page 24: Z Grills Support
Z GRILLS SUPPORT Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Dealer's name and date of purchase 2.Purchaser's name, phone number and address 3.Z GRILLS model number, serial number and part identification numbers... - Page 25 Onlyfire, Inc. shall not be liable if you install, operate, clean or maintain your grill without following the owners' manual instructions. Misuse, abuse, alteration and natural disasters...