MoltenVoltage PEDAL SYNC OZ Owner's Manual

MoltenVoltage PEDAL SYNC OZ Owner's Manual

Advertisement

Quick Links

OZ™ is a stand-alone MIDI controller for the Strymon TimeLine Delay's LOOPER mode, which
unlocks TimeLine's MIDI-only LOOPER features including Undo, Redo, Half-Speed and Reverse. OZ also
allows soft-switch, single-touch record/playback, external LOOP LEVEL control, and automatic DRY
LOOPER recording.

Key Features

Transforms the Strymon TimeLine Delay into a full-featured, high-fidelity, state-of-the-art LOOPER
Unlocks the hidden potential of the
Strymon TimeLine delay by accessing its
MIDI-only LOOPER features:
Reverse loop direction instantly
HALF-SPEED playback and recording
with LED Speed indicator. TIP: record
at half-speed to create double-speed
playback!
Undo back to initial loop
Redo overdubs (after pressing UNDO)
Single-press, soft-touch recording and
playback - Press and Hold the
REC/PLAY Button while recording and
the loop automatically enters Play Mode
on release, making loop timing far
easier and more accurate than pressing a second button
DRY Switch automates the use of TimeLine's LOOPER mode without any Delay Effect by setting the
MIX to zero (guitar only) upon Record
Loop Level control - adjust in real-time, or set it and forget it (auto-adjust on Record)
info@PedalSync.com
Congratulations on purchasing OZ™ by Molten Voltage
OWNER'S MANUAL
© 2013 - MoltenVoltage.com - All Rights Reserved.
v 1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PEDAL SYNC OZ and is the answer not in the manual?

Questions and answers

Summary of Contents for MoltenVoltage PEDAL SYNC OZ

  • Page 1 DRY Switch automates the use of TimeLine's LOOPER mode without any Delay Effect by setting the MIX to zero (guitar only) upon Record • LOOP LEVEL control - adjust in real-time, or set it and forget it (auto-adjust on Record) info@PedalSync.com © 2013 - MoltenVoltage.com - All Rights Reserved. v 1.1...
  • Page 2 (E) LOOP LEVEL Control (F) Remote Footswitch RECORD Jack (optional) (G) RECORD/PLAY Button (H) HALF/FULL SPEED Button (I) SPEED LED (J) REVERSE Button (K) REDO Button (L) UNDO Button info@PedalSync.com © 2013 - MoltenVoltage.com - All Rights Reserved. v 1.1...
  • Page 3 Overdub Mode so the loop does not reset. TIP: Molten Voltage prefers to Hold when making the initial loop, but Tap for overdubbing info@PedalSync.com © 2013 - MoltenVoltage.com - All Rights Reserved. v 1.1...
  • Page 4 This is true even if multiple overdubs have been recorded. Note that a loop must be playing for the Undo function to work. Pressing the REDO Button (K) adds back in all overdubs. Note that new overdubs recorded after pressing UNDO erase all prior overdubs. info@PedalSync.com © 2013 - MoltenVoltage.com - All Rights Reserved. v 1.1...
  • Page 5 Range will be set for Firmware before 1.43. If HALF/FULL SPEED is held on power up, the Red LED will flash. When released, OZ’s Loop • Level Range will be set for Firmware 1.43 and later. info@PedalSync.com © 2013 - MoltenVoltage.com - All Rights Reserved. v 1.1...
  • Page 6 If REDO is held on power up, Red LED will flash, on release, MIDI Channel 15 will be used Consult the TimeLine manual for simple instructions on how to change its MIDI Channel. MIDI Phantom Power OZ does not use MIDI Phantom Power. info@PedalSync.com © 2013 - MoltenVoltage.com - All Rights Reserved. v 1.1...
  • Page 7 MIDI repeater. If you are daisy chaining MIDI devices, the total MIDI cable length must be considered if any MIDI devices do not amplify the data signal. Support info@PedalSync.com info@PedalSync.com © 2013 - MoltenVoltage.com - All Rights Reserved. v 1.1...
  • Page 8 PedalSync, CTL-Sync, OZ, MASTER CONTROL, TEMPODE, NODE, Tru-Foot, Molten Voltage, Visionary Effects, ReMute, “Sturdy Scalable Simple”, “streamline your sound”, “Design simple Design sublime”, and “the future just showed up” are all trademarks of Molten Voltage. Legal@MoltenVoltage.com info@PedalSync.com © 2013 - MoltenVoltage.com - All Rights Reserved. v 1.1...

Table of Contents