User’s manual REVO KP 3 Important warnings for safety The unit are integral part of industrial equipments. When it is supply, the unit is subject to dangerous tensions. Don’t remove the plastic cover. Don’t use this unit in aerospace and nuclear application. Electric Shock Hazard (Rischi di scosse elettriche, Risque de choque électrique) When thyristor unit has been connected to main supply voltage and is switched off, before to touch it be secure that the unit is isolated and wait at least one minute to allow discharging internal capacitors.
Page 3
User’s manual REVO KP 3 Warranty condition Producer gives a 12 months warranty to its products. The warranty is limited to repairing and parts substitution in our factory and does exclude products not properly used and fuses. Warranty does not include products with serial numbers deleted. The faulty product should be shipped to Producer at customer’s cost and our Service will evaluate if product is under warranty terms.
User’s manual REVO KP 3 Wiring and dimensions 3.1 REVO-KP 4.3’’ (CE Version) Pin serial Port CN1 (D-sub 9pin, female) Signal Name Description Tx/Rx - Data – (Blue) Tx/Rx + Data + (Brown) 3.1.2 Dimensions and fixing holes Top View 119mm [4.685"]W x 93mm[3.661"]H 128mm [5.039"] Cutout dimensions...
User’s manual REVO KP 3 3.2 REVO-KP 7’’ (CE Version) Pin serial Port CN1 (D-sub 9pin, male) Signal Name Description Tx/Rx - Data – (Blue) Tx/Rx + Data + (Brown) 3.2.1 Dimensions and fixing holes 200.4mm [7.89"] 192mm [7.56"] 192mm [7.559"]W x 130mm [5.433"] H Front View Side View Cutout dimensions...
User’s manual REVO KP 3 3.3 Wirings Wiring with REVO C series D-sub 9 pin Blue Brown Terminal Block M3 Terminal Block M1 Terminal Block M1 Terminal Block M5 REVO C REVO C REVO C REVO C from 30 to 40A from 60 to 210A from 300 to 800A from 1100 to 2100A...
User’s manual REVO KP 3 Installation Before installation, make sure that the product has not been damaged during transport. In case of damage, notify the carrier immediately. Verify that the product is indeed the one ordered. For mounting use the supplied brackets. To connect the 24Vdc power supply using the supplied clamp.
User’s manual REVO KP 3 Operation The panel is configured to communicate with the static relays CD Automation series REVO C and REVEX. 5.1 Functional description 5.1.1 Numeric fields 1 2 3 The BLUE values are read-only. 1 2 3 The BLACK values, if enabled, are read/write.
User’s manual REVO KP 3 5.2 Menu By pressing the key the navigation Menu will appear. Level 1 Level 2 Function keys 6 lines display 4 lines display Calls up the page to log in at a different level Calls up the version information page Calls up the Serial Communication Status page REVO-KP3 configuration...
User’s manual REVO KP 3 5.3 Home page The home page can be 4 or 6 lines Each line can be configured on the configuration page depending of the connected device (REVO C or REVEX) or available service (diagnostic screens communication, or reading analog inputs). Here there are some examples: 4 zones setting 6 zones setting...
Page 13
User’s manual REVO KP 3 5.3.2 Actions on the main page 5.3.2.1 ZOOM on REVO C / REVEX zone Tap the bar graph or the states and you will enter the Zoom area Here i’ts possible to - Set input type (Level 1): •...
Page 14
User’s manual REVO KP 3 5.3.2.2 Reference Set Tap the % value and a window will appear with REVO C / REVEX Here it’s possible to set the input type (Level 1) • Digital: Controlled by REVO-KP3 • Analog: Controlled by Analog Input Set the % value when Digital 5.3.2.3 Enabling and disabling a zone Tap the PW value and a...
User’s manual REVO KP 3 5.3.2.4 Trend Tap the Trend icon a window will appear with REVO C / REVEX Reference: 0-100% Voltage: 0-operative voltage + 10% Power: 0-100% Average current: 0-load current + 10% the trend has a 10 minute window, data out of the window can no longer be seen 5.4 Log In Press to access this page...
User’s manual REVO KP 3 5.5 Configuration/Reset Level 5.5.1 Zones configuration Press to access this page with 6 zones with 4 zones...
Page 17
User’s manual REVO KP 3 5.5.1.1 Zone names Tap the Name to customize the 6 characters text with an alphanumeric keypad 5.5.1.2 Type Tap the Type to select the instrument type For the 6th and 3d zone is possible to set them as measures from analog input boards or serial state...
Page 18
User’s manual REVO KP 3 5.5.1.3 Starting page Tap “Start with” to set the starting page Set to 4 zones Set to 6 zones 5.5.1.4 Language Tap “Language” to set the language...