Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ETS WHITESUN VELOCITY 918HP
- Page 1 VELOCITY 918HP WHITESUN Solarium for body tanning Technical Manual User’s Manual For approved replacement parts and other questions contact: 1-800-449-3605 7445 Company Drive, Indianapolis, IN 46237-9296 Whitesun S.r.l - Via Filippo da Recco 21 D - Recco (Ge) Italy 27041-01A Revised 2/18/05...
-
Page 2: Table Of Contents
VELOCITY CONTENTS 1.0 INTRODUCTION page 03 2.0 WARNINGS page 04 Table of recommended exposure time page 04 2.1 INSTRUCTIONS page 06 2.2 DOCUMENTATION & ACCESSORIES page 08 3.0 INSTALLATION page 09 3.1 MACHINE POSITIONING page 10 3.2 POWER SUPPLY CONNECTION page 10 4.0 USE page 11... -
Page 3: Introduction
VELOCITY 1.0 INTRODUCTION PAY ATTENTION – IMPORTANT This new equipment is user-friendly. However, in order to achieve the best results, it is important to carefully read this manual and follow all the instructions contained in it, before operating the equipment for the first time, since the manual provides important directions regarding the safety of installation, use and maintenance. -
Page 4: Warnings
VELOCITY 2.0 WARNINGS DANGER Ultraviolet radiation. Follow instructions. Avoid overexposure. As with natural sunlight, overexposure can cause eye and skin injury and allergic reactions. Repeated exposure may cause premature aging of the skin and skin cancer. WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES. - Page 5 VELOCITY WARNING Read the instructions booklet before using this sunlamp product. All persons in the room should wear protective eyewear when lamps are on. Recommended eyewear: provided eyeshields or equivalent eyewear as defined under 21 CFR 1040.20. Other types of eyewear may not provide adequate protection.
-
Page 6: Instructions
VELOCITY 2.1 INSTRUCTIONS (to standard CEI EN60335-1/EN 60335-2-27/98 and amendments) Artificial tanning is nowadays a widespread practice. In this field, however, there is still great confusion regarding the possible risks that may be incurred by those who practice artificial tanning. In this matter, it should be reminded that light is subdivided as follows, according to wavelength: wavelength lower than 280 nanometers (UV-C);... - Page 7 VELOCITY INFORMATION AND PRECAUTIONS Ultraviolet sunlight radiation or UV equipment may cause damage to the skin or to the eyes. These biological effects depend on the quality and quantity of the radiation as well as on the skin and eye sensitivity of the individual person.
-
Page 8: Documentation & Accessories
VELOCITY CONDUCT OF THE PROFESSIONAL PERSONNEL IN THE PRACTICE OF TANNING WITH HIGH PRESSURE UV-A EQUIPMENT Before exposing the customer to irradiation, the attending professional personnel shall: • have customer always use protective eye-wear • verify customer’s skintype before exposure •... -
Page 9: Installation
VELOCITY 3.0 INSTALLATION PAY ATTENTION TO THESE FUNDAMENTAL RULES DO NOT CARRY OUT ANY OPERATION WITH POWER ON 1. After packaging has been removed, check that the equipment is in good order and complete. In particular, make sure it has not been visibly damaged during transportation. 2. -
Page 10: Machine Positioning
VELOCITY IMPORTANT The machine must be connected to an exhaust hose for the forced hot air produced by the lamps cooling. The hose’s maximum length can be no longer than 5 meters (16 feet), with one bend having an angle of 90° maximum. -
Page 11: Use
VELOCITY 4.0 USE The use of any electrical equipment requires the compliance with some fundamental rules. In particular: 1. Do not touch the machine with wet or damp hands. 2. Do not pull the power supply cord to move the machine. 3. -
Page 12: Operating Procedures
VELOCITY 4.1 OPERATING PROCEDURES To use, lie down on contoured acrylic. Keep your body, including arms and legs, in contact with the contoured acrylic surface as shown. Use of other positions may result in overexposure. SELECTING THE SESSION TIME In order to immediately change the session time, press the TIME BUTTON to decrease the session time. -
Page 13: Keyboard Functions
VELOCITY 4.2 KEYBOARD FUNCTIONS LCD DISPLAY SHOWING SETTINGS BUTTONS FOR INCREASING OR DECREASING BODY FAN SPEED START BUTTON (TURNS ON) STOP BUTTON (TURNS OFF) BUTTONS FOR COLUMN POSITION 4.3 OPERATING FUNCTIONS Body Fan Speed. Press the + or – button to increase or decrease fan speed. -
Page 14: Preventive Measures And Maintenance
VELOCITY 5.0 PREVENTIVE MEASURES AND MAINTENANCE Before carrying out any maintenance, disconnect the machine from the power supply source by switching off the circuit breakers located both on the machine and at the service panel. 1. Lamps must be replaced after 500-600 hours of operation. 2. - Page 15 VELOCITY CHANGING FILTER-GLASS 1. Unclip the four latches securing the acrylic and swing the acrylic open. 2. Remove the screws securing the filter-glass holding bracket as indicated in Figure b-1 and replace the filter. 3. Close the acrylic and secure the latches. B - 2 B - 1 B - 3...
- Page 16 VELOCITY CHANGING THE LAMPS 1. Disconnect the machine from the power source. 2. Open the column acrylic. 3. Open the filter-glass holding frame and keep it open with the special stop. 4. Make sure the lamp is not hot. 5. Carefully remove the lamp from the lamp socket. 6.
-
Page 17: Cleaning
VELOCITY 6.0 CLEANING Before carrying out any cleaning, disconnect the machine from the power supply source by switching off machine’s and installation’s circuit breaker. • For cleaning the external structure, use a soft and slightly damp cloth. Never use gasoline, chemical solvents, thinners and their derivatives. -
Page 18: Suggestions And Trouble-Shooting
VELOCITY 7.0 SUGGESTIONS AND TROUBLE-SHOOTING Always disconnect the machine from the power source before carrying out any check. • To check whether lamp is defective, substitute it for another.. Never touch it with the hands. • Make sure that all machine’s closures and covers are properly closed after any check. •... -
Page 19: Technical Characteristics
VELOCITY 8.0 TECHNICAL CHARACTERISTICS 8.1 VELOCITY 918HP Overall rated power: 18,900 VA Lamps make-up: 2 x 600 W 12 x 800 W 4 x 1000 W General characteristics Input voltage: 220 – 230 V AC Frequency: 50 / 60 Hz Type of current: three-phase Lamps cooling airflow capacity:... -
Page 20: Warranty Conditions
VELOCITY 9.0 WARRANTY CONDITIONS The conditions described below are essential conditions for the validity of the warranty. The equipment is warranted for a period of 24 (twenty four) months from the date of installation. The warranty will operate in case of replacement of parts of the equipment whose malfunction is exclusively due to workmanship defects. - Page 21 VELOCITY COMPULSORY CONDITIONS FOR THE INSTALLATION OF THE MACHINE It is absolutely compulsory for the purchaser requesting this equipment to observe the following requirements: Technical inspection by a qualified firm to determine whether the grounding system to which the machine will be connected is in perfect operating condition.
-
Page 22: Statement Of Compliance
VELOCITY 9.1 STATEMENT OF COMPLIANCE STATEMENT OF COMPLIANCE 73/23/CEE and 93/68CEE This equipment satisfies the safety requirements set forth by Directive 83/392 EMC since it is constructed in compliance with harmonized standards. We draw the attention on the following facts that may jeopardize the compliance as well as the characteristics of the equipment: WRONG POWER SUPPLY WRONG INSTALLATION...
Need help?
Do you have a question about the WHITESUN VELOCITY 918HP and is the answer not in the manual?
Questions and answers