Advertisement
DO NOT use the heater with a programmer, timer or any other device that switches the heater on automatically.
8
DO NOT touch the lamps, even when cold.
8
DO NOT allow children to touch or to operate the heater.
8
DO NOT locate the heater below an electrical socket outlet.
8
DO NOT use the heater without the grille fitted.
8
DO NOT use the heater out of doors. These heaters are designed for indoor use only.
8
DO NOT use this heater if it has been dropped.
8
DO NOT use if there are visible signs of damage to the heater.
8
DO NOT cover heater when in use, and do not obstruct the air inlet and outlet grilles.
8
DO NOT place heater too close to yourself or any object, allow the air to circulate freely.
8
DO NOT touch the outlet grille of the heater during and immediately after use as it will be hot.
8
WARNING: The fireguard of this heater is intended to prevent direct access to heating elements and must be in place when the heater is
‰
in use.
WARNING: The fireguard does not give full protection for young children and for infirm persons.
‰
Children of less than 3 years should be kept away unless continuously supervised.
9
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in
9
its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe
way and understand the hazards involved. Children aged from 3 years to less than 8 shall not plug in, regulate and clean the appliance or
perform user maintenance.
This appliance can be used by children aged from 8 years and above and persons with physical, sensory or mental capabilities or lack
of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
2. INTRODUCTION
Electric heater with infrared quartz lamp. Suitable for wall or overhead mounting. Reaches maximum heat output within seconds of being turned
on. Supplied with 1.3m power cable and mounting bracket. A totally dry heat with no condensation, no gas, no fumes and no smell.
3. SPECIFICATION
Model No: ....................................................... IR12 / IR12CT
Fuse Rating: ....................................................................13A
Minimum Mounting Height: ............................................ 1.8m
Mounting Bracket Stand-Off: ...................................... 134mm
Overall Dimensions IR12 (W x D x H) .......412 x 95 x 210mm
Overall Dimensions IR12CT (W x D x H) 1100 x 1100 x 1490mm
Plug Type: ......................................................................3-Pin
Power Supply Cable Length: ......................................... 1.3m
Power ..........................................................................1200W
Supply ............................................................................230V
4. INSTALLATION
4.1.
WALL MOUNTING (IR12)
4.1.1.
MOUNTING LOCATION
WARNING: Locate the unit no closer than 0.3m to the ceiling, no less than 1.8m
‰
from the floor and no less than 1m from any side wall.
WARNING: Ensure the mounting surface is suitable and strong enough to securely
‰
and safely mount the unit (fixings not supplied).
4.1.2.
Remove the four screws on the rear of the unit and use these to attach the unit mounting bracket to the unit with it's orientation
arranged in order to facilitate downward adjustment of unit when fitted to the wall mounting bracket. Ensure all fixings are
firmly and securely attached.
4.1.3.
Attach the wall mounting bracket to the mounting surface using suitable fixings (not supplied).
4.2.
STAND MOUNTING (fig.1)
NOTE: Stand Mounting using IRCT Tripod (not supplied, can be bought in conjunction with IR12 in model number IR12CT).
4.2.1.
Fit adaptor to the unit mounting bracket with the M8 hexagon head screw, washer and nut. Tighten screw to obtain grip without clamping
the heater bracket totally. The heater angle can be adjusted by rotating about this fixing. Tighten securely after adjustment.
4.3.
The tripod will be supplied assembled. Retract plunger at base of upright and pull or push central column tube through sleeve until the
plunger "clicks" into the location hole. This will be the stands maximum height setting.
4.4.
Slide the handle down the central column and fix with the thumb screw through the M8 hole.
4.5.
Slide adaptor c/w heater into central column to full depth and clamp with thumb screw.
5. OPERATION
WARNING! DO NOT touch the top of the heater when in use as it becomes hot.
‰
WARNING! Always allow elements to cool before moving the unit. Failure to do so will cause premature wear to the lamp and reduce its
‰
working life.
WARNING! This heater is not equipped with a device to control the room temperature. DO NOT use this heater in small rooms when
‰
occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
5.1.
POWER ON/OFF
5.1.1.
Connect to mains supply and use rocker switch set to either "I" for low power or "II" for high. Set rocker switch to "O" to turn off.
5.2.
ANGULAR ADJUSTMENT (Wall mounted only)
5.2.1.
To adjust the angle of the unit, loosen the hinge bolt, remove the angle locking screw and rotate the unit such that the alternative
locking screw hole can used. Tighten the hinge bolt to firmly and securely clamp the unit at the new angle.
© Jack Sealey Limited
Original Language Version
fig.1
Shows IR12CT
IR12 / IR12CT Issue:1 03/04/23
Advertisement
