Advertisement
Quick Links
Advertisement
Summary of Contents for Yuel Beast Designs ATLAS Series
- Page 1 CALYPSO Calypso User guide Version 8...
- Page 2 The performance-first design values of the ATLAS series, in a smaller ITX footprint. The CALYPSO chassis gives you all the watercooling potential needed for the current AND next generation of hardware. No longer choose between performance & aesthetics. Build up an AIO, single custom loop, dual loop or hybrid to support even the most demanding components.
- Page 3 Calypso Overall Dimensions...
- Page 4 Calypso ATX Assembly & Dimensions 260mm | 11" Calypso SFX Assembly & Dimensions 242mm | 9.5" 208mm | 8"...
- Page 5 Calypso PSU Types Calypso ATX PSU For ATX PSU Mounting. Supports two 2.5" drive mounted either horizontally or vertically Calypso SFX PSU For SFX PSU Mountning. Supports two 2.5" drive mounted horizontally...
- Page 6 Calypso GPU Disambiguation Standard GPU Bracket Standard GPU Bracket The Standard GPU Bracket supports regular GPU Mounting for graphics cards up to 336mm Long Adapter GPU Bracket & Armature Enhanced GPU Adapter Bracket Standard Armature In order to recieive a regular Armature, an enhanced GPU bracket must be used.
- Page 7 Calypso GPU Mounting Change your GPU mounting position based on the number of PCIE slots your graphics card occupies. The standard GPU Bracket (Shown above) can accommodate up to 3 GPU positions (.8" movement). The Adapter GPU bracket has even more flexibility than the standard bracket and can mount in 2X as many positions.
- Page 8 Standard gpu Mounting clearance The Standard GPU Bracket is shown in its second of three possible mounting positions. The distance from edge of GPU Bracket to Radiator Panel varies based on where you decide to mount the GPU bracket. 1'st Position (For single Slot cards) = 46mm 2nd Position = 26mm 3rd Position = 5mm...
- Page 9 adapter & Armature gpu Mounting clearance The adapter GPU Bracket & Armature are shown in its closest of seven mounting positions. The distance from edge of the Armature to Radiator Panel varies based on where you decide to mount the GPU bracket. 4rth Position = 31mm 1'st Position = 61mm 5th Position = 20mm...
- Page 10 adapter & Armature gpu limitations One of the few limitations of the Armature & GPU Adapter bracket is a setup in which the wings are attached above and below the motherboard while using a horizontal motherboard layout (The standard GPU Bracket works fine in this and any orientation). The built in solution to this is simply not using the raidator bracket for the side with the GPU.
- Page 11 Calypso Wing 328mm ID Dimension to flanges Approximately 320mm to radiator bracket attachment hardware The Calypso Wing allows for 240 & 280 radiator mounting, with headroom clearance of 44mm (240mm rad) and 24mm (280) respectively. Additionally the 240mm radiator can jog 5mm, and 280mm radiator 9mm in either direction from center.
- Page 12 Calypso Radiator Brackets Pump Radiator The Hybrid radiator Bracket brackets unique design allows for the passthrough of fittings and bulkheads on most radiators The Pump Radiator bracket allow for the mounting of any pump matching a 40mm or 60mm Hybrid Radiator mounting Bracket pattern...
- Page 13 Calypso Radiator Bracket mounting 26mm All dimensions +/- 1mm 360mm Fan pattern on Center Each Radiator Bracket supports 120mm, 140mm, 240mm, 280mm, and 360mm radiator pattern. A 360mm fan pattern is joggable 14mm from center in either direction.
- Page 14 Calypso Assembly Standard GPU Bracket 10-32 Hex Nut for Wings 6-32 SHMS for Motherboard 10-32 SHMS & Washer for Wings Motherboard Plate Wing...
- Page 15 Calypso Assembly Continued I personally prefer the motherboard plate to be Note GPU Bracket installed ontop of the installtion is on this side of wings, but there is no right the motherboard panel or wrong way to install this component When assembling CALYPSO, it is important to not fully tighten all the components until all peices are assembled in their relative positions.
- Page 16 Calypso Assembly Continued 10-32 SHMS / Washer for SFX & ATX PSU Hole for Power button or Pass-through Clearance holes for the 6-32 SHMS, Washer, & Hex nut for Radiator Bracket attachment. Each Radiator bracket has four attachment points, two on each wing...
- Page 17 Calypso Assembly Continued Stabalizer brackets, prevents tipping in alternative orientations...
- Page 18 Troubleshooting and Notes to user Washers are recommended, but completely optional and partially aesthetic. Please DO NOT use a washer on your motherboard as this will most likely cause damage. Each Calypso Package comes with a bag labeled "Troubleshooting", this bag contains a 6-32 & 10-32 Type F Screws.
- Page 19 Please visit our website for our current return policy, terms of service, privacy policy, and other important information. www.yuelbeast.com contact@yuelbeastdesigns.com © Yuel Beast Designs, 2022 Calypso User guide Version 8 Updated 11/2/22...