Components list 1. Base assembly 3. Right side panel 2. Left side panel assembly assembly 4. Top assembly 5. Rear panel assembly 6. Internal door frame 8. Internal acoustic 7. Internal acoustic assembly panel left panel right Tone Acoustic Booth Assembly Instructions v1.0 Page 3...
Page 3
Fixings 9. Door 10. Carpet 38 Pieces 3 Pieces M8 x 40mm Cap head M8 x 140mm cap head bolt silver bolt silver PU floor cushion 8 Pieces M10 x 16mm CSK socket head bolt black 11. Upholstered side panel x2 34 Pieces M8 x 25mm Washer silver...
Page 4
Unpack the booth components Carefully remove the booth components from the delivery container and remove protective packaging. Place the components in a safe place where they can be free from damage and protect edges from hard surfaces. Heavy! Two person lift required. Tone Acoustic Booth Assembly Instructions v1.0 Page 7...
Page 5
Position the base Level the base Spirit level 8mm Socket Please ensure the base is in the correct location before assembly, allowing a minimum of 1 meter around the base and 2.5 meters of height clearence. 2500mm 1000mm 1000mm 1000mm 1000mm Tone Acoustic Booth Assembly Instructions v1.0 Tone Acoustic Booth Assembly Instructions v1.0...
Page 6
Remove foam from side assemblies Fit left side panel assembly M8 Washer silver 6mm Hex key M8 x 40mm cap head bolt Rubber mallet PU floor cushion Heavy! Two person lift required. Left side assembly Right side assembly Remove two sections Remove three sections PU floor cushion Finger tight...
Page 7
Fit right side panel assembly Remove floor access panel M8 Washer silver 6mm Hex key M8 x 40mm cap head bolt Rubber mallet PU floor cushion Heavy! Two person lift required. PU floor cushion Remove the panel by removing 2 x 4mm x 45mm CSK woodscrews Finger tight...
Page 8
Fit back panel assembly Fix back panel assembly M8 Washer silver M8 x 40mm cap head bolt 6mm Hex key Heavy! Two person lift required. Support the glass frame whilst fixing. Fix with 10 No. M8 x 40mm cap head bolts and washers Rest the rear panel on the base assembly...
Page 9
Position top panel assembly Fix top panel assembly M8 Washer silver M8 x 40mm cap head bolt Rubber mallet Heavy! 6mm Hex key Two person lift required. Cables Fix with 8 No. M8 x 40mm cap head bolts and washers Finger tight Ensure ceiling cable passes...
Page 10
Fit front door frame panel assembly interior Fit front door frame panel assembly exterior M8 Washer silver M8 Cap head bolt cover M8 x 40mm cap head bolt silver M8 x 40mm cap head bolt silver M8 x 15mm washer 6mm Hex key 6mm Hex key Finger tight...
Page 11
Align side panels and tighten all fixings Replace floor panel 6mm Hex key 24mm Plywood Spacer Use the plywood spacer to set the depth of the side panels with the front and back panel edges to 24mm. Fix the panel with 2 x 4mm x 45mm Align both sides Ensure the depth...
Page 12
Connect electric cables Fit the shelf bracket M10 x 16mm CSK bolt 6mm Hex key Connect the electric cables to the top and bottom of the right hand panel assembly Tone Acoustic Booth Assembly Instructions v1.0 Tone Acoustic Booth Assembly Instructions v1.0 Page 22 Page 23...
Page 13
Replace foam - right panel assembly Replace foam - left panel assembly Tone Acoustic Booth Assembly Instructions v1.0 Tone Acoustic Booth Assembly Instructions v1.0 Page 24 Page 25...
Page 14
Fit the carpet Fit the internal right side panel Fit the carpet to the floor of the booth, ensuring the carpet is flat. Fit the panel with the pre-applied hook and loop tape, taking care over the shelf bracket. Push all around the edges and down the centre from top to bottom to ensure the...
Page 15
Fit the internal left side panel Fit the shelf and trim M10 x 16mm CSK bolt 6mm Hex key Slide the shelf trim over the shelf supporting bracket. Fit the panel with the pre-applied hook and loop tape. Push all around the edges and down the centre from top to bottom to ensure the...
Page 16
Fit the upholstered left side panel Fit the upholstered right side panel Connect the Z - Bars to hang the panel. Connect the Z - Bars to hang the panel. Tone Acoustic Booth Assembly Instructions v1.0 Tone Acoustic Booth Assembly Instructions v1.0 Page 30 Page 31...
Page 17
Fit door Fit door handles M8 cap head bolt cover 6mm Hex key M8 x 140mm cap head bolt Door handle spacer M8 x 15mm washer Heavy! Two person lift required. Outer door handle Holding the door at 90 degrees to the booth, lift and drop down to engage the hinges.
Page 18
Test door seal and magnetic catch Adjust door closure and magnetic catch 3mm Hex key Plastic magnet spacer shims (0.5mm; 1.0mm) Magnetic catch assembly Self-adhesive cover M5 x 25mm CSK screw Magnet Plastic shim Plastic shim Magnetic Door should soft closure close and hold to magnet to provide a...
Page 19
Tone Acoustic Booth Assembly Instructions V1.0 Copyright 2022...
Need help?
Do you have a question about the Screen Solutions Tone Acoustic Booth and is the answer not in the manual?
Questions and answers