Page 1: Table Of Contents
If you are not entirely satisfied with this Introduction product, please return it to the nearest ALDI store within 60 days from the BRUSH CUTTER 31CC date of purchase, for a full refund or replacement, or take advantage of our Layout after sales support by calling the supplier’s Customer Service Hotline.
Page 2: Pack Contents/Parts
Overview Utilisation Pack contents/parts Fig. 1 Fig. 4 Fig. 5 Pack contents/parts Brush cutter 31cc (4 stroke) 3 teeth blade Nylon cutting head Fig. 6 Fig. 7 Shoulder strap Loop (P-) handle Spark plug wrench Allen key 4mm Allen key 5mm Cable tie Fig.
Page 3: Handling Pictures
Handling pictures Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig. 18 Fig. 19...
Page 4 Handling pictures Fig. 21 Fig. 20 Fig. 22 Fig. 23 Fig. 24 Fig. 25 Fig. 26 Fig. 27...
Page 5 Handling pictures Fig. 29 Fig. 28 Fig. 31 Fig. 30 Fig. 33 Fig. 32 WIND CORD Fig. 35 Fig. 34...
Page 6 Handling pictures Fig. 36 Fig. 37 Fig. 38 Fig. 39 Fig. 40 Fig. 41 Fig. 42 Max. Min.
Page 7: Explanation Of Symbols
Explanation of symbols Explanation of symbols Read the instruction manual. Warning! Petrol is very flammable. Avoid smoking or getting any flame or sparks close to fuel. Warning! Denotes risk of personal injury, loss of life, or damage to the tool in case of non-observance. Warning! Risk of injury! Do not let your hands or feet come in contact with the blades when the motor is running.
Page 8 Explanation of symbols Conforms to relevant standards for electromagnetic compatibility. Caution kickback! Caution, do not use saw blades or multi-part metal cutting tools! Brush cutter Grass trimmer Guaranteed sound power These operating instruction provide places concerning your m ATTENTION! safety which are marked with this indication. Failure to follow these instructions may cause light to medium m CAUTION! risk of injury.
Page 9: Introduction
Introduction I. Introduction Congratulations on choosing to buy a FERREX product. ® All products brought to you by FERREX are manufactured to the highest standards of per- ® formance and safety, and as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 3 Year Warranty.
Page 10: Layout
Layout 2. Layout (Fig. 1 - 31) 1. Petrol tank 2. Rear handle 3. Front handle 4. Star knob 5. Long handle with drive shaft 6. Safe guard 7. Cutting blade 8. Cutting blade safe guard 9. Filler cap 10. Air filter housing cover 11.
Page 11: Scope Of Delivery
Scope of delivery/ Intended use 3. Scope of delivery • Open the packaging and take out the equipment with care. • Remove the packaging material and any packaging and/or transportation braces (if available). • Check to see if all items are present. •...
Page 12: General Safety Instructions For Power Tools
Intended use/ General safety instructions for power tools m IMPORTANT! Due to the high risk of bodily injury to the user, the petrol brush cutter must not be used to carry out the following work: to clean dirt and debris off walkways, or to chop up tree or hedge clippings.
Page 13 General safety instructions for power tools d. Do not abuse the cord. Never use the cord for carrying, pulling or un- plugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
Page 14 General safety instructions for power tools which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Page 15 General safety instructions for power tools Additional Safety Rules for Petrol products • Do not operate in a hazardous location. Such areas include where there is a risk of explosion of petrol fumes, leaking gas or explosive dust. • Do not operate in a confined area. Exhaust gases, smoke or fumes could reach dangerous concentrations.
Page 16 General safety instructions for power tools/Before starting the equipment • Prior to operation, ensure the assembled line Grass Trimmer is checked for loose components and the operating controls of the trimmer. Do not use the Grass Trimmer if the controls are not in perfect working order. Ensure all nuts, bolts and clamps are all tight.
Page 17: Before Starting The Equipment
General safety instructions for power tools/Before starting the equipment/Attachment and operation ter blade contacts anything it cannot cut. This contact may cause the 3T brush cutter blade to stop for an instant, and suddenly “thrust” the unit away from the object that was hit. This reaction can be violent enough to cause the oper- ator to lose control of the unit.
Page 18 Attachment and operation 7.1.2 Mounting the shaft (Fig. 6) • Push the lower part of the long handle with drive shaft (5) right down until the locking pin (27) slots into the bore for locking pin (28) in the shaft. This is easier to do if you rotate the bottom of the long handle with drive shaft (5) slightly in both directions.
Page 19 Attachment and operation 7.1.5 Fit the shoulder strap (21) (Fig. 16-19) • As shown in Fig. 16, fit the shoulder strap well. When closing the shoulder strap you will hear a noticeable click. • The shoulder straps can be adjusted according to your size. •...
Page 20 Attachment and operation Check before use! • Check the safe condition of the device. • Check the device for leaks. • Check the device for visual defects. • Check that all parts of the device have been securely fitted. • Check that all safety devices are in proper condition. m Danger of injury! Before starting work, always check the ground and remove all objects which could be thrown by the device.
Page 21: Working Instructions For Brush Cutting And Line Trimming
Attachment and operation/Working instructions for Brush Cutting and Line Trimming Note: If there is a problem, press the switch On/Off (18) to the OFF position (Fig. 25), to stop the machine running. To stop the cutting head from running,, release the throttle lever (17). (Fig. 25) If any problem occurs, pull the emergency release (22), then release the brush cutter immediately.
Page 22 Working instructions for Brush Cutting and Line Trimming 8.3.1 Low trimming Hold the trimmer right in front of you at a slight angle so that the underside of the line spool is above the ground and the line strikes the correct target. Always cut away from yourself. Never draw the trimmer towards yourself.
Page 23: Maintenance And Cleaning
Maintenance and Cleaning 9. Maintenance and Cleaning m ATTENTION! Sharp edges. For all work on and around cutting tools always wear protec- tive gloves. When not in use, transport or storage always mount transport protection on all cutting tools. m WARNING! Before performing any maintenance or cleaning work, always turn off the en- gine and pull out the spark plug boot.
Page 24 Maintenance and Cleaning 9.2 Grinding the safety hood blade The safety hood blade can become blunt over time. • When you notice this, undo the screw holding the safety hood blade on the safety hood. • Clamp the blade in a vise. •...
Page 25 Maintenance and cleanig 9.5.2 Changing the oil (Fig. 41-42) • Change the engine oil every year before the start of the season when the engine is warm. • Use only engine oil (SAE30 / 10W30). • Open the oil filler neck ( 15). •...
Page 26: Storage
Storage/Technical data 10. Storage Storing the unit After cutting, clean the unit thoroughly. Store the unit in a dry room allow the motor to cool down beforehand. Storage m IMPORTANT! Never put the equipment into storage for longer than 30 days without carry- ing out the following steps.
Page 27: Technical Data
Technical data 11. Technical data Cutting data grass trimmer Cutting circle diameter of line mm Cutting line diameter mm 2 x 2.4 Cutting line length m Max. cutting speed max. min 6200 Cutting data brush cutter Cutting circle diameter of blade mm Cutter blade thickness mm Teeth quantity Max.
Page 28 Technical data Maximum measured sound power level: Brush cutter LwA: 102.3dB(A) K= 3dB(a) Grass trimmer LwA: 105.4dB(A) K= 3dB(a) Wear ear-muffs. The impact of noise can cause damage to hearing. Measured vibration values: Brush cutter: Idle Left handle: 3,038m/s² Right handle: 2,062m/s² Brush cutter : Racing Left handle: 4,771m/s²...
Page 29: Disposal And Recycling
Disposal and recycling Kapitelüberschrift 12. Disposal and recycling The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Defective components must be disposed of as special waste.
Page 30: Troubleshooting
Troubleshooting Kapitelüberschrift 13. Troubleshooting Fault Possible Cause Remedy • Correct starting procedure not • Follow the instructions for starting followed. • Clean the spark plug or replace it The equipment • Sooted or damp spark plug. with a new one. does •...
Page 31 Kapitelüberschrift...
Page 32: Warranty Details
BRUSH CUTTER 31cc Warranty Details REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION The product is guaranteed to be free from defects in workmanship and parts for a period of 36 months from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our discretion.
Page 33 Kapitelüberschrift...
Page 34: Repair And Refurbished Goods Or Parts Notice
Please be assured though, refurbished parts or replacements are only used where they meet ALDI’s stringent quality specifications. If at any time you feel your repair is being handled unsatisfactorily, you may escalate your complaint.