Contents INTRODUCTION ............................1 ..........................1 ANUFACTURER ERVICE ......................... 2 DECLARATION OF CONFORMITY PREPARATION OF INFORMATION ......................3 ........................3 YMBOLS AND DESIGNATIONS ..........................4 NSTRUCTIONS AND LISTS SAFETY..............................5 ......................... 5 ASIC SAFETY INSTRUCTIONS .............................. 7 ROPER USE ............................7 MPROPER USE TECHNICAL DATA .............................
1.1 Manufacturer/Service Carl Stahl Hebetechnik GmbH Tobelstrasse 2 73079 Suessen Phone +49 (0) 7162 4007 – 0 E-mail carlstahl@carlstahl.com Internet www.carlstahl-hebetechnik.de INFO We will be happy to answer any questions you may have about your product. - 1 - www.carlstahl-hebetechnik.de...
Content of the document: For the product designated below Name: Textile Bridle Sling we hereby declare that it corresponds to the basic requirements specified in the harmonization legislation named below: DIRECTIVE 2006/42/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of May 17, 2006 about machines and the change of Directive 95/16/EC (new version) –...
In a warning, steps are marked with and structured chronologically. Pictographs for specific hazards Meaning: Warning about suspended load. Meaning: Warning about danger of crushing. Meaning: Warning about hand injuries. The pictographs are used in connection with the associated classification and the appropriate signal word. - 3 - www.carlstahl-hebetechnik.de...
Instructions that do not have to be carried out in a particular sequence are marked as follows: Step Step The result of an action is marked with an arrow: Result or device reaction Lists are marked with dashes: - List www.carlstahl-hebetechnik.de - 4 -...
- Make sure that these operating instructions are always available where the Textile Bridle Sling will be used; - Make sure that only qualified staff performs work with and on the Textile Bridle Sling (see Tab. - During use, comply with the applicable requirements for occupational safety and the work instructions of the operator;...
Page 9
- Product-specific knowledge - Safe handling of load lifting devices, professional Use, simple visual Specialized personnel inspection training and experience - Knowledge of the regulations for proper disposal and Disposal Specialized personnel re-use Tab. 1: Overview www.carlstahl-hebetechnik.de - 6 -...
- The angle of inclination of a leg greater than 60°C; - Use and storage outdoors. - Hook the round sling directly into the crane hook. Chapter 3.3 does not guarantee completeness. Anything that is not expressly permitted falls under improper use. - 7 - www.carlstahl-hebetechnik.de...
If parts are missing or damaged, contact the manufacturer/dealer (Chapter 1.1). 5.2 Transport The Textile Bridle Sling is tested, checked and packed properly before delivery. Delivery is made using a suitable transport system. Always transport the Textile Bridle Sling using a suitable transport system.
Layout and function 6. Layout and function The Textile Bridle Sling consists essentially of the following components: Fig. 1: Textile Bridle Sling Position Name Oblong master link Inspection Data Tag / Identification Tag Roundsling Clevis Hook Roundsling coupler Roundsling coupler Tab.
Read Chapter 8, especially 8.2-8.4. The inspection is intended to ensure that the sheet metal clamp is in perfect condition and ready for operation. Before using the Textile Bridle Sling, you must observe the following with regard to the work environment: DANGER Danger to life due to falling load! A falling load can cause severe injuries or death.
The hook tip must not be loaded. The safety latch or flap must be closed. If multi-leg Textile Bridle Slings are used, the hook tips must point outwards. Fig. 2: Direct lifting www.carlstahl-hebetechnik.de - 12 -...
The Textile Bridle Sling must be cleaned, maintained, and inspected regularly. For the maintenance/inspection intervals, see the maintenance/inspection plan. 8.1 Cleaning INFO Regular cleaning and careful handling mean that the Textile Bridle Sling will be in good condition throughout its life cycle. Component Cleaning criteria...
- etc. Tab. 6: Maintenance/inspection plan 8.4 Inspection criteria The discard criteria for the Textile Bridle Sling are determined using the inspection criteria in the following table. For the basic value, specified in mm, see Technical data (see Chapter 4). Component...
Servicing 8.5 Visual inspection and function check Before each use, the Textile Bridle Sling must be checked and inspected. The tables in Chapter 8.4 list criteria which may indicate that you must take the sheet metal clamp out of service.
Disposal of sheet metal clamp NOTICE ABOUT DISPOSAL If the Textile Bridle Sling can no longer be repaired or if it is no longer functional, it must be disposed of in accordance with the applicable legal provisions. Disposal of packaging material...